Reference: RBD-1155

3.6V Micro Hydro Generator

Built-in Lipo Charging Circuit Stabilized Voltage Output High Battery Capacity

Reference: RBD-2759

MicroSD Card Module

Allows MicroSD cards to be written and read

Reference: RBD-2068

7DOF Aluminum Alloy Robotic Arm Manipulator with Gripper and MG996R servo

Aluminum alloy mechanical arm body. Total weight 902 gram with servos and gripper. Color silver. 7 MG996R metal servo. Assembled

Reference: RBD-2760

RS422 to TTL Power Supply Converter Board

RS422 interface, two-way communication. B Y Z A ultra far transmission 1000 meters The module has ESD 15KV protection. Onboard to increase the limit of 10 ohms current limiting current protection. Module with TVS diode. Anti lightning, peak voltage. The module has 120-ohm termination resistors, which can effectively reduce the interference of long-range...

Reference: RBD-0404

Brand: RoboticsBD

4 DOF Robotic Arm Wooden DIY Unassembled

7 reviews

4 DOF Robotic Arm wooden DIY unassembled Premium quality kit with wood cutting parts and screws Includes 4 SG90 servos for joint motion Untrammeled and flexible motion with 4 degrees of freedom Product's color maybe different, local material is used.  If any parts got broken during setup, please email us at ask@roboticsbd.com. We may not charge you for...

Reference: RBD-2761

ICL8038 12V to 15V 10Hz-450KHz Triangular/Rectangular/Sine Wave Signal Generator Module

ICL8038 12V to 15V, Signal Generator, Medium/Low Signal, Frequency 10Hz-450KHz, Triangular/Rectangular/Sine Wave Generator, Module Working voltage: 12V ~ 15V Output: Triangular wave, Square wave and sine wave. Frequency range: 10HZ ~ 450kHz Low distortion sine wave: 1% Duty cycle range: 2% to 98% Low temperature drift: 50ppm / ℃ Triangular wave output...

Reference: RBD-0581

Mini Round Double Deck Chassis Kit 2WD

1 review

Outline Size: 135 x 135 x 80mm The round acrylic plate diameter: 130mm Another acrylic plate size: 135 x 75mm

Reference: RBD-2769

Mini MP3 and WAV File Player

Model MP3-TF-16P / FN-M16P

Reference: RBD-2798

I/O Expander - MCP23008

Add another eight pins to your microcontroller using a MCP23008 port expander. The MCP23008 uses two I2C pins which can be shared with other I2C devices, and in exchange gives you eight general purpose pins. You can set each of eight pins to be input, output, or input with a pullup. There's even the ability to get an interrupt via an external pin when any...

Reference: RBD-2832

Roller Lever Endstop Limit Switch Module

Designed for use as an endstop for 3D printers but it can be used for other contact detection applications as well.

Reference: RBD-2833

Impact Switch Collision Switch Sensor Module

Type: Vibration Sensors Output: Switching Transducer Dimensions: 25 x 14 x 6 (LxWxH) mm Weight: 3 gm

Reference: RBD-2834

A4988 / DRV8825 Stepper Motor Driver Expansion Board

Enhance your 3D printer's performance with the DRV8825/A4988 Stable 42 Stepper Motor Driver Expansion Board. This expansion board offers advanced features and superior performance to meet your diverse needs in 3D printing and DIY projects.Note: Please ensure correct installation direction of the drive module to prevent module damage.

Reference: RBD-2473

34mm Mini Car N20 Motor Rubber Small Wheel

Diameter: 34 mm D axis diameter: 3mm Tire width: 6.5 mm Suitable for mini Robots and Hobby kits.

Reference: RBD-2487

Hiwonder 6 Channel Digital Servo Tester with Over-Current Protection

6-channel PWM digital servo controller Supports a wide variety of PWM servos High-accuracy potentiometer for precise servo control Servo reset function 0.09° control accuracy 3-channel overcurrent protection Compact and lightweight design

Reference: RBD-2513

5V Electromagnet - 25 Kg Holding Force - P40/20

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 25 Kg / 55 lb Approximate Pickup Weight: 5 KgEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and...

Reference: RBD-2858

Dual Voltage Comparator Module

Multi-Sensor Support: Works with various sensors like NTC thermistors, TCRT5000 line followers, and force sensors. Precise Control: Dual potentiometers for fine-tuning sensor thresholds. Wide Voltage Compatibility: LM393 chip ensures adaptability to diverse power sources. Compact & Durable Design: Integrates seamlessly into projects with a robust build.

Reference: RBD-2514

5V Electromagnet - 10 Kg Holding Force - P30/22

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 10 Kg / 22 lb Approximate Pickup Weight: 2 Kg / 4 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through...

Reference: RBD-2892

ESP8266 ESP-01 ESP-01S DHT11 Temperature and Humidity WiFi IOT Sensor Node

Model: SNA118 Material: Plastic Plastic Type: PC Tool Supplies: CuttingDoes not Include ESP Wireless Module

Reference: RBD-2515

5V Electromagnet - 5 Kg Holding Force - P25/20

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 5 Kg / 11 lb Approximate Pickup Weight: 1 Kg / 2 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through...

Reference: RBD-2919

MAX98357A I2S DAC Class D Mono Amplifier Module

This mono Class D amplifier module with a surprisingly compact form factor - less than 2cm on a side - uses a MAX98357 chip to deliver 3W of power. Its I2S input allows an easy association with a Raspberry Pi or ESP32, allowing for example to design a small portable amplified speaker.

Reference: RBD-2516

5V Electromagnet - 2.5 Kg Holding Force - P20/15

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 2.5Kg / 5.5lb Approximate Pickup Weight: 0.45 Kg / 1 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current...

Reference: RBD-2920

2.42 inch OLED Screen LCD Display Module 128x64 SSD1309 SPI 7Pin White

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: SPI (default) Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2518

Plastic Water Solenoid Valve - 12V - 1/2" Nominal

1 review

1/2" Nominal NPS Working Pressure: 0.02 Mpa - 0.8 Mpa Working Temperature: 1 ℃ - 75 ℃ Response time (open): ≤ 0.15 sec Response time (close): ≤ 0.3 sec Actuating voltage: 12VDC Actuating life: ≥ 50 million cycles

Reference: RBD-2921

2.42 inch OLED Screen LCD Display Module 128x64 SSD1309 SPI 7Pin Yellow

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: SPI (default) Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2922

2.42 inch OLED Screen LCD Display Module 128x64 IIC I2C 4Pin White

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: I2C Communication Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2533

QTR-8A Reflectance Sensor Array

2 reviews

This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate analog voltage output.Note:...

Reference: RBD-2923

2.42 inch OLED Screen LCD Display Module 128x64 IIC I2C 4Pin Yellow

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: I2C Communication Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2925

2.4GHz Wireless Transceiver Module NRF24L01 Green 10pin

125 Channels, Multi-point communication, and frequency hopping to meet the communication needs Built-in hardware CRC error detection, Multipoint communication address control. Low-power 1.9 ~ 3.6V, only 1uA on Power-down mode Built-in 2.4Ghz antenna Built-in voltage regulator Standard DIP Pitch Interface for embedded applications size: 34mm X 17mm X 1mm

Reference: RBD-2928

RF Transceiver Radio Module nRF905 433/868/915MHz with Antenna

Radio module (transmitter and receiver) operating in 433 MHz band with SPI communication interface. Powered by 2.7 V - 3.3 V, the outputs are goldpin connectors.It has an external antenna with SMA connector.

Reference: RBD-2573

Cap Conductive Slip Ring 6 Wire

A slip ring is an electromechanical device that allows the transmission of power and electrical signals from a stationary to a rotating structure. A slip ring can be used in any electromechanical system that requires rotation while transmitting power or signals. It can improve mechanical performance, simplify system operation and eliminate damage-prone...

Reference: RBD-2939

Brand: DFRobot

RS485 Shield for Arduino

RS485 is an industrial standard for long-distance, anti-interference, and reliable communication. The Arduino RS485 shield, specially designed for the Arduino Uno board. It converts UART/Serial protocol to the RS485 protocol.  This RS485 board allows Arduino talk to industrial devices. In contrast to RS-422, which has a single driver circuit that cannot...

Reference: RBD-2611

QTR-8RC Reflectance Sensor Array

This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate digital I/O-measurable output.