Reference: RBD-0349

Digispark Kickstarter ATTINY85 Arduino General Micro USB Development Board

31 reviews

Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...

Reference: RBD-2484

Brand: Arduino Official

Arduino UNO R4 WiFi Development Board Original

1 review

The new Arduino UNO R4 development board comes in two versions: the UNO R4 WiFi and the UNO R4 Minima. It runs on the Renesas RA4M1 (Arm Cortex®-M4) processor with a clock speed of 48MHz, which provides a 3x increase over the UNO R3. In addition to that, the SRAM has been upgraded from 2kB to 32kB and the flash memory has been increased from 32kB to 256kB...

Reference: RBD-2483

Brand: Arduino Official

Arduino Opta Lite Micro PLC (Ethernet and USB-C ports)

Arduino Opta, specially designed for PLC engineers, is a secure, easy-to-use micro PLC with industrial IoT capabilities. Opta is equipped with frequently used networks and protocols in multiple industries, and supports both Arduino sketch and standard PLC languages, including LD (Ladder Logic Diagram) and FBD (Function Block Diagram). Its powerful...

Reference: RBD-0352

Knock Sensor Module KY-031

4 reviews

Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD

Reference: RBD-2490

Arduino Ethernet Shield W5100 R3

1 review

Support TCP/IP protocol: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE and Ethernet Built-in 10BaseT/100BaseTX Ethernet physical layer Support automatic communication handshaking(full duplex and half duplex), Support automatic MDI/MDIX, automatically revise signal polarity Support ADSL connection (support PAP/CHAP certification mode in PPPoE protocol), Support...

Reference: RBD-0354

TSL2561 Luminosity & Infrared Light integrating sensor

Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD

Reference: RBD-2499

Brand: Arduino Official

Genuine Arduino Nano ESP32 with headers

1 review

Made in ITALY Powerful and versatile Arduino board based on ESP32-S3 Compatible with Arduino and MicroPython programming Easy to use and ideal for beginners and advanced users alike Perfect for IoT and MicroPython projects

Reference: RBD-0355

HC-020K Speed Measuring Module With Speed Encoder Kit

4 reviews

Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line

Reference: RBD-2551

3.5inch LCD Display Shield for Arduino with Touch

Supports development boards such as Arduino UNO and Mega2560 for plug-in use without wiring 480X320 resolution, clear display Support 16-bit RGB 65K color display, display rich colors 8-bit parallel bus, faster than serial SPI refresh On-board 5V/3.3V level shifting IC, compatible with 5V/3.3V operating voltage Easy to expand the experiment with SD card...

Reference: RBD-2568

Arduino UNO R4 WiFi

1 review

The Arduino UNO R4 WiFi merges the RA4M1 microprocessor from Renesas with the ESP32-S3 from Espressif, creating an all-in-one tool for makers with enhanced processing power and a diverse array of new peripherals. With its built-in Wi-Fi® and Bluetooth® capabilities, the UNO R4 WiFi enables makers to venture into boundless creative possibilities....

Reference: RBD-0358

I2C Bi-Directional Logic Level Converter- 2 Channel

2 reviews

Dimensions: 11×15 x 2 (L x W x H) mm Weight: 1gm Mutual transform between 5V TTL and 3.3V TTL Two channels of logic and high voltage low voltage logic can two-way transform Portable and lightness, with 2 rows 4 pin contact pins

Reference: RBD-2569

Arduino UNO R4 Minima

Arduino Uno R4 Minima High-Quality Edition (Made in China)  Introducing the Arduino UNO R4 Minima! This board boasts the RA4M1 microprocessor from Renesas, delivering increased processing power, expanded memory, and additional peripherals. And the best part? It stays true to the reliable UNO form factor and operates at a practical 5 V voltage. Brace...

Reference: RBD-0368

Force Sensitive Resistor 0.5"

2 reviews

Thickness: 0.4mm Trigger Force: 20g, triggered (default resistance<200kΩ)  Pressure Measuring Range: 20g~6kg Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz) Initial Resistance: >10MΩ Activation Time: <0.01S Operating Temperature: -40°C~+85°C  Lifespan: >1million times Hysteresis: +10%，(RF+ -RF-)/FR+，1000g...

Reference: RBD-2651

Wemos D1 Mini V3

D1 Mini board with 4 MB flash memory and ESP8266 chipset. The board can be programmed with Arduino IDE, has the CH340 USB chipset and allows you to create IoT devices quickly and easily.

Reference: RBD-2652

Wemos D1 Mini NodeMCU

Firstly, In terms of pins, the D1 Mini and NodeMCU V3 development boards are quite similar. They both break out all ESP8266 ESP-12E/F pins. The NodeMCU V3 board has additional 3V3 and GND pins. Hence,  it is more suitable for various connections to devices with an additional button for the flash. Furthermore, you can flash either board with NodeMCU...

Reference: RBD-2679

STM32F103C8T6 ARM STM32 Minimum System Development Board Module

STM32F103C8T6 ARM Development Board Module with Type-C Interface and Enhanced Memory Enhance your embedded system projects with the STM32F103C8T6 ARM development board module. Featuring a Type-C interface for easy connectivity, this module offers seamless one-click download capability. With an upgraded BOOT switch, you can easily perform upgrades without...

Reference: RBD-2752

Arduino Uno R4 Minima

Arduino Uno R4 Minima Standard-Quality Edition (Made in China)Arduino UNO R4 Minima is armed with a powerful 32-bit microcontroller courtesy of Renesas. Brace yourself for increased processing power, expanded memory, and a whole new level of on-board peripherals. The best part? Compatibility with existing shields and accessories remains intact, and...

Reference: RBD-0379

TS832 RC832 Boscam 5.8G 32CH 250mW FPV Transmitter Receiver 7.4-16V

1 review

TS832 RC832 5.8G 32CH 250mW FPV Transmitter Receiver 7.4-16V

Reference: RBD-2764

ESP32-S3-WROOM-1-N16R8 UNO Development Board For DevKitC-1

The ESP32-S3-WROOM-1-N16R8 is a versatile Wi-Fi and low-power Bluetooth MCU module, featuring the advanced ESP32-S3 series chip. With its powerful performance, rich peripheral interfaces, and support for popular programming methods, this module offers a wide range of applications in various fields including IoT, AI, and smart devices.

Reference: RBD-0382

GY-87 10DOF MPU6050 HMC5883L BMP180 Sensor Module

1 review

3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD

Reference: RBD-2765

ESP32-S3 CAM Development Board WiFi Bluetooth Module N16R8 OV5640 Camera

The ESP32-S3 WROOM Development Kit 2 is a comprehensive development solution based on the ESP32-S3-WROOM-1 module, featuring an onboard PCB antenna and advanced peripherals. This kit comes bundled with an OV5640 camera, providing a complete hardware platform for prototyping and developing IoT, AI, and wireless communication applications.

Reference: RBD-0383

ADS1115 16 Bit I2C 4 channel ADC Module

1 review

Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference

Reference: RBD-2789

ESP32-S3 CAM Development Board WiFi Bluetooth Module N16R8 OV2640 Camera

The ESP32-S3 WROOM Development Kit 2 is a comprehensive development solution based on the ESP32-S3-WROOM-1 module, featuring an onboard PCB antenna and advanced peripherals. This kit comes bundled with an OV2640 camera, providing a complete hardware platform for prototyping and developing IoT, AI, and wireless communication applications.

Reference: RBD-0385

MCP23017 I2C 16 Input/Output Port Expander

2 reviews

IC Name: MCP23017 Package/Case: DIP-28

Reference: RBD-0386

Precision Real Time Clock Module DS3231 AT24C32 I2C

29 reviews

1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.

Reference: RBD-0621

USB to Mini USB Cable 1M - Arduino NANO

Connects Your Arduino Nano: Provides essential connection between your Arduino Nano and a computer for programming and power. Standard Compatibility: Features USB Type-A and Mini-B connectors for universal computer connectivity. Reliable Performance: Solid workmanship and high-quality materials ensure dependable data transfer. Flexible Design: 1-meter...

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

14 reviews

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-2886

Arduino Esplora Joystick Photosensitive Sensor Board

Microcontroller: ATmega32u4 Operating Voltage: 5V Flash Memory: 32 KB of which 4 KB used by bootloader SRAM: 2.5 KB EEPROM: 1 KB Clock Speed: 16 MHz Made in China

Reference: RBD-0390

12V 37GB550 Gear Motor High Torque 60 RPM

3 reviews

Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).

Reference: RBD-2887

NodeMcu Lua ESP8266 WiFi Development Board CP2102 Driver - Type-C interface

The Development Kit based on ESP8266, integrates GPIO, PWM, IIC, 1-Wire and ADC all in one board. Power your development in the fastest way combine with NodeMCU Firmware! R2 version had CP2102 USB-TTL instead, larger current support, slim board can put on breadboard. Programing it with Arduino IDE. High quality USB cable is needed for this board to give...

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

1 review

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...