Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-0390
DC 12V 60 RPM 37GB-550 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-0218
High Torque Gear Motor 12V, 50 RPM Volt: DC 12V RPM: 50 Torque 13KG/CM
Reference: RBD-0267
Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...
Reference: RBD-0376
Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes
Reference: RBD-0727
Operating Voltage: 12VDC Power Consumption: 1.42 W Body and Blade Constructed from Thermoplastic PBT of UL 94V-0 Single Phase 4 Pole Brushless DC Motor Precise Vapo Bearing Counterclockwise Rotation Direction if Viewed from front of Fan Blade
Reference: RBD-1250
DC 12V 195 RPM 37GB-545 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-1315
Great bio-compatibility, excellent transparency and environment-friendly Low shrinkage, good round shape Accurate diameter (±0.02mm) Easy to print with stable printing performance Various colors are available 100% bio-degradable and FDA food safety approved
Reference: RBD-1390
Nema17 Bipolar. Number of Phases: 2. Step Angle: 1.8°. Phase Voltage: 2.6Vdc. Phase Current: 1.7A. Resistance: 1.5Ω ±10%. Inductance: 2.8mH ±20% (1KHz). Number of Wire: 4 (100cm Length). Holding Torque: 43N.cm. Shaft Diameter: Ø5mm. Motor Length: 40mm. Mass: 270g.
Reference: RBD-1565
MODEL: Robotic Arm Edge Kit based on OWI-535 WEIGHT: 4.00kg DIMENSIONS: 40.00cm x 30.00cm x 8.50cm
Reference: RBD-1872
Product: Water Pump Model: AD20P-1230C Voltage: 12V Current: 350mA. Power consumption: 3.6W.
Reference: RBD-2067
7-70V 30A PWM DC Motor Speed Controller Switch Wide voltage input range: 7-70V Maximum output current: 30A Speed control knob with switch function Adjustable potentiometer with flexible cable (15cm length) Includes a 30A fuse for motor interface protection Input power must be 1.5 times greater than the motor's rated power
Reference: RBD-2107
Great bio-compatibility, excellent transparency and environment-friendly Low shrinkage, good round shape Accurate diameter (±0.02mm) Easy to print with stable printing performance Various colors are available 100% bio-degradable and FDA food safety approved
Reference: RBD-2182
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below.
Reference: RBD-2436
Brand: Creality Official
Creality Ender-3 V3 SE 3D Printer Max printing speed of 250mm/s and 2500mm/s² acceleration Auto leveling with CR Touch & Strain Sensor for precise prints "Sprite" Direct Extruder for PLA, PETG, and flexible TPU Stable Dual Z-axis and Y-axis Dual Linear Shafts for reliable printing Auto filament loading and unloading for easy filament changes
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-1244
Aluminum body with high torque metal gear servos 6 DOF structural design makes the robot arm move flexibly Up to 17Kg torque for joint servos Various control ways
Reference: RBD-2437
Brand: Creality Official
Build area: 300 x 300 x 400 mm Maximum print head temperature: 300°C Maximum bed temperature: 100°C Communication: WiFi, USB Supported materials: PLA, ABS, PETG, TPU, PA, and carbon fiber composites.
Reference: RBD-0306
Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android
Reference: RBD-0309
4 poles 12 slot Hi-torque motor design CNC machined 6061 T6 windings maximizes efficiency High RPM ABEC5 oversize bearings Universal fit, fit all 1/10 brushless cars-multi-mounting system for M3 screws Precision balanced rotor, smoothness for best reliability and maximum RPM
Reference: RBD-1733
Brand: Creality Official
Built-in WIFI function: Remote control printing anytime, anywhere; A Bit More Intelligence Ultra-silent Design: 32 Bit Mute Board and Mute Fan Design; Intelligent Auto-leveling: V2.0 Auto leveling way, is the same with CR-6 SE. Screen Protection & Auto-shutdown;. Safe and worry-free save energy and power. 6-steps to assemble 8 minutes to complete,...
Reference: RBD-2123
STM32 chip for the main controller Easy Visual Operation Interface Support wireless handle control, smart phone APP and mouse control Provide graphical PC software and detailed tutorials The current Stock comes unassembled.
Reference: RBD-0217
Model: MG90S Weight: 13 gm Operating voltage: 4.8V~ 6.6V Servo Plug: JR Stall torque @4.8V : 1.8kg-cm Stall torque @6.6V : 2.2kg-cm Note: The component, colour & shape of the motor may vary depending on our stock rotation.
Reference: RBD-0375
AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)
Reference: 1403
Brand: Creality Official
Replaced with New Version Creality Ender-3 V3 SE 3D Printer. Click Here
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-0377
Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD
Reference: 1404
Brand: Creality Official
Modeling Technology: FDM(Fused Deposition Modeling) File Formats: STL/OBJ/AMF Slicer Software: Creality Slicer/Cura/Reptier-Host/Simplify3D Print Speed: 80-100mm/s Resume Print Function: Yes Printing Size: 235x235x250mm
Reference: RBD-2045
Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD