Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0028
Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet. Stackable Design, can directly be supported by for Arduino official Ethernet Library. Supports up to four simultaneous socket connections Can be used to store files for serving over the network. Can be accessed using the Mini SD TF library. IEEE802.3af...
Reference: RBD-0927
Weight: 85 gm. Voltage : 11.1 V. Dimensions : 17 x 34 x 72(mm ). Max Continuous Discharge : 25 C(25 A). Balance Plug : JST-XH. Discharge Plug : XT-60.
Reference: RBD-0929
Weight : 97 gm Voltage: 11.1V Capacity: 1500mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
Reference: RBD-1258
Model No: XW Power Eagle Lipo 1000mAh 7.4V 2S 25C Lipo Battery (T Plug Connector) Weight: 76 gm. Voltage: 7.4V. Dimensions : 26x34x72 (mm ). Max Continuous Discharge : 25C(25A). Balance Plug: JST-XH. Max Burst Discharge: 90 C (50A). Discharge Plug: T-Plug.
Reference: RBD-1259
Model No: XW Power Eagle Lipo 1500mAh 7.4V 2S 25C Lipo Battery (T Plug Connector) Weight: 76 gm. Voltage: 7.4V. Dimensions : 26x34x72 (mm ). Max Continuous Discharge : 25C(25A). Balance Plug: JST-XH. Max Burst Discharge: 90 C (50A). Discharge Plug: T-Plug.
Reference: RBD-1909
6v 2800mah AA NI-MH Battery Rechargeable Battery Pack JST Plug
Reference: RBD-2712
Tired of constantly replacing and disposing of 9V batteries for your electronics projects or robots? The Rechargeable DoublePow 9V Battery 280mAh with DP-D01 Charger is the perfect solution for you. This package includes both a high-capacity rechargeable battery and a versatile charger to meet your power needs efficiently and sustainably. Save Money...
Reference: RBD-0108
Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards. Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host) Supports HID devices, such as keyboards, mice, joysticks, etc. Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard...
Reference: RBD-0928
Voltage : 11.1V Constant Discharge : 30C(10.5A) Max discharge : 25C (10 sec) Dimensions : 74 x 34 x 22 (LxWxH)(mm ) Weight : 87 gm Charge Rate : 1-3C Recommended, 5C Max
Reference: RBD-0270
AD/DA IO interface : screw terminal 1-WIRE interface : for connecting 1-WIRE devices like DS18B20 Sensor interface : for connecting various sensors 0.96inch OLED : SSD1306 driver, 128×64 resolution, SPI interface Buzzer CP2102 : USB TO UART converter PCF8591 : 8-bit AD/DA converter, I2C interface
Reference: RBD-0494
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: STD-120200
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-1087
Uninterruptible Power Supply Mini UPS Modem, Router, CCTV Camera and Lighting 6000mAh 22.2W
Reference: RBD-1343
Compatible With: AA, AAA, 9V Battery red light show the charging situation 9V Battery Charger
Reference: RBD-0914
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCB Dimensions: 128×32 (LxW) mm
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-1038
Reset button. 4M crystal onboard, Using socket, Crystal frequency can be replaced easily at any time 4 independent push buttons, connected to RB0 RB1 RB2 RB3 8 LED's connected to the RD port, J3 is jumpered to enable LED. Remove to disconnect. Standard RS232 communication interface, microcontroller computer communication interface.
Reference: RBD-1218
Model No.:NX8048T050 Display Type:011R(R:Resitive Touchscreen) Operating Voltage (VDC):4.75 ~ 7 Max. Operating Current (mA):410 Touch Type: Resistive Colors:65K (65536)
Reference: RBD-1874
Suitable for DIY & Hobby Kits, Routers, and Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved.
Reference: RBD-1876
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 1.8. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. Model: HS 121800
Reference: RBD-1684
8 Channel DC 12V Pro mini Relay Shield Module PLC Timer Board for Arduino
Reference: RBD-2175
4-port charger for single-cell 3.7V LiPo batteries Uses MCP73831T Charge Management Controller IC for reliable charging Standard Mini USB socket for 5V USB power source Selectable charging rates of 500mA or 100mA (default set to 500mA) Status LED indicates charging status Suitable for 3.7V LiPo or Li-ion batteries with Micro JST Connector USB charger...
Reference: RBD-1759
Brand: Waveshare
Display Resolution: 200 x 200 Display Screen Color: Black and White No backlight so keeps displaying last content for a long time even when the power is down Ultra low power consumption, basically power is only required for refreshing SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.
Reference: RBD-2255
The Doublepow Smart Battery Charger (DP-D03) is a 4 slot charger. It has an input of AC110-240V 50/60Hz. It has output of DC 1.2V 180mA D/C DC1.2V 150mA AA/AAA DC9V 25mA 9V, making it suitable for charging 1.2V AA/AAA/C/D/9V Ni-MH/Ni-CD rechargeable batteries.
Reference: RBD-2377
Universal battery charger for AA, AAA, and 9V Ni-MH or Ni-CD batteries Can charge 2-4 AA or AAA batteries at once, or 1 or 2 9V batteries Charging current of 200mA for AA batteries and 150mA for AAA batteries LED indicators show the charging status Compact and portable design
Reference: RBD-1929
General-purpose HDMI display, Connecting computers, TV boxes, Microsoft Xbox360, SONY PS4, Nintendo Switch and so on Can be used as Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, Win10 IOT, single-touch, free drive Can be used as PC monitor, support Win7, Win8, Win10 system (No touch Function)
Reference: RBD-2697
Create your own high-capacity power bank with this DIY case for 6 x 18650 batteries (not included). Dual USB outputs allow charging two devices simultaneously. Triple input ports provide flexibility for charging the power bank itself. Integrated LCD display shows charging status and battery level. Compact and portable design for convenient carrying. Note:...
Reference: RBD-1947
Operating Voltage: 12V DC Equipped with high-current relay 10A 250VAC / 10A 30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection. Freewheeling diode to protect your microcontroller. Input Signal Pin connected to Burg...
Reference: RBD-2709
Reliable & Protected Power: 7.4V, 3500mAh Li-ion battery pack with built-in BMS for safe operation. Pre-assembled Convenience: Features high-quality 18650 cells (2S2P configuration) and XH2.54-2P connector for easy integration. Compact & Lightweight: Ideal for portable applications in speakers, robots, and various electronic devices. Long-lasting...
Reference: RBD-1948
Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off Note: Relay might be...
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-2945
27W power delivery for fast and efficient charging. Type-C connector compatible with various devices. Wide input range (100-240V) for worldwide use. Reliable output of 5.5V at 3.0A. Lightweight and compact for easy portability.