How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0660
Material: glass fiber Can connect 1-4 ESC. RoboticsBD This has an XT60 plug to connect a battery.
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-0353
Driver IC: SSD1306 Support wide voltage: 3.3V-5V DC Communication: IIC Working temperature: -30-80 degrees. RoboticsBD
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0729
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0736
Model: 720 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Current: 0.1 A. Rated RPM: 48000. Max Speed: 50000 RPM. Wire Length: 5cm Prop. Length: 55mm
Reference: RBD-0741
Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-2264
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire. Motor Shaft coupling not included buy it here.
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-0912
Model: 8020 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Rated RPM: 39000. Wire Length: 6cm Prop. Length: 55
Reference: RBD-2141
Rating contract (Max.): 10 W Switching power supply (Max.): 110VDC Resistance contract (Max.): 100 Ω Appro. Float Ball Size (mm) : 24×17 (LxD) Body Total Length (mm) : 85 Cable Length (cm) : 37 Total Float opening: 70° Switch ON/OFF angle Approx. betn 15° to 20°
Reference: RBD-1073
3.7V 600mAh 25C Lipo battery Product Type: Lithium Polymer Battery Pack The LiPo battery has matched resistance. Good Temperature Control. Minimum weight in Class
Reference: RBD-1400
4-Channel Relay interface board and each one needs 15-20mA Driver Current. Both controlled by 12V and 5V input Voltage. Equipped with high-current relay, AC250V 10A ; DC30V 10A. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low). Indication LED’s for Relay output...
Reference: RBD-0684
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
Reference: RBD-1321
Product Type: Multi Purpose Propeller: 10 Inch
Reference: RBD-1950
Card reader MF522-MINI module uses the RC522 original chip to design the Supply Voltage 3.3V Works at a 13.56MHz frequency
Reference: RBD-0834
Glue Gun Sticks Hot melts easy use Multipurpose Perfect for home repairs, hobbies and crafts, Standard sealing wax sticks require less reloading. AC 100 V - 240 V, 50 Hz / 60 Hz Glue gun Uses standard hot melt glue sticks Fold-out stand for safe handy storage while in use. RoboticsBD
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-1570
Length: 9″. Pitch: 4.7″. Weight: 20 gm. Shaft Diameter: 7.86 mm. Total Length: 9 inch / 225 mm. Material: ABS
Reference: RBD-1571
Length: 10″. Pitch: 4.5″. Weight: 25 gm. Shaft Diameter: 9.5 mm. Total Length: 10 inch / 250 mm. Material: ABS
Reference: RBD-0980
Dimensions : 66 x 66 x 3 mm. Weight : 25 gm. Supply Voltage : 5 VDC. Interface : IO . 8 x 8 = 64 RGB. Chip : WS2812.
Reference: RBD-1572
Length: 11″ Pitch: 4.7″ Weight: 27 gm Shaft Diameter: 7.86 mm Total Length: 28 cm Includes a set of reducers (3,4,5,6 mm)
Reference: RBD-0981
Low power device. DTMF decoder chip. Band-split filter. Digital decoding functions. Modem interfaces. Mobile radios.
Reference: RBD-0987
Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-0429
High precision determination accurate to 1 Lu for different lights Operating Voltage: 3-5VDC Built-in 16bit A/D converter I2C interface
Reference: RBD-1065
Latest Arduino CNC Shield Version 3.10 GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) Coolant enable Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) Compact design. 4-Axis support (X, Y, Z, A-Can duplicate...
Reference: RBD-1753
Digital I2S interface with high precision 24-bit dataHigh signal to noise ratio is 61 dBAHigh sensitivity – 26 dBFSStable frequency response from 60 Hz to 15 kHzLow power consumption: low current consumption 1.4 mAHigh PSR: -75 dBFS
