Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0378
Model: Eachine 1000TVL 1/3 CCD Lux: 0.08Lux/ F1.2 Sensor: 1/3 “CCD Format: NTSC/PAL(Free switch) Resolution: a.Ultra High Definition 1000TVL b.PAL: 976H X 582V c.NTSC: 976H X 494V Lens: 2.8mm IR coated. RoboticsBD FOV: 110 °
Reference: RBD-2268
Features WiFi+Bluetooth connectivity with the ESP-WROOM-32 module Accessible I/O pins via extension headers for easy customization Onboard USB CH340 for convenient programming and debugging 2x keys for reset or user-defined functions ESP32S-DEV development board is a cost-effective solution for a wide range of applications.
Reference: RBD-1746
Neodymium Magnet Shape: Disc Dimension: 10mm x 1mm
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0741
Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-2050
Driver IC: SH1106 Resolution: 128 x 64 Visual Angle: >160° Input Voltage: 3.3V Pixel Color: Blue If you want to purchase White color 1.3 inch OLED display module click here
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0912
Model: 8020 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Rated RPM: 39000. Wire Length: 6cm Prop. Length: 55
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-1073
3.7V 600mAh 25C Lipo battery Product Type: Lithium Polymer Battery Pack The LiPo battery has matched resistance. Good Temperature Control. Minimum weight in Class
Reference: RBD-1060
Perfectly fit on the extruder Noiseless Performance Very low Current consumption Easy to install and connect.
Reference: RBD-1338
Easy to Assemble High-Quality Components Brushed Quadcopter
Reference: RBD-1387
Memory Size: 128 Gigabyte Card Type: Micro SD Speed: up to 95MB/s Class: 10 High-speed Card can be used for both Mobile phone and Raspberry Pi
Reference: RBD-0564
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-1924
Use for convert battery with Deans to XT60 on ESC / charger. Excellent performance, solid and secure connection, safety in use. High quality and compact,easily to add the adapter. No wires design can save more space.
Reference: RBD-0990
Support any Chinese text, English text synthesis, and support for English mixed Support voice codec function, the user can use the chip for direct recording and playback Support speech recognition function, can support the recognition of 30 command words.
Reference: RBD-1925
Use for convert battery with Deans to XT60 on ESC / charger. Excellent performance, solid and secure connection, safety in use. High quality and compact,easily to add the adapter. No wires design can save more space.
Reference: RBD-1098
Interface: I2C Operating Voltage: 3-5VDC Ports: 8-bit Parallel Ports Can be used with Arduino and Raspberry Pi
Reference: RBD-0163
Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V Output voltage range (corresponding to 0-100%RH) DC 1-3.19V Test accuracy 5% RH
Reference: RBD-0315
Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm. RoboticsBD
Reference: RBD-1328
Size: 0.96 inch Resolution: 128 x 64 Controlling Chip: SSH1106 Display Area: 21.74 x 10.86mm Driving Voltage: 3.3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White
Reference: RBD-2582
Displays a single digit using bright green LEDs Common cathode configuration for simple wiring 10 pins for easy connection Clear visibility and compact size Ideal for various electronic projects
Reference: RBD-2629
Diameter 3mm and Length 30 (M3 x 30) Round Machine Screw (Countersunk)
Reference: RBD-2696
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-0350
100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.
Reference: RBD-1816
Anti-Interference Ability Baud rate: 110 ~ 256000bps Operating Voltage: 3v to 30VDC Compatible With Both 3V and 5V logic