Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0388
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. RoboticsBD Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0919
Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-1305
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common anode No. of Pins: 10 Low Current Consumption High Brightness
Reference: RBD-1421
3S 11.1V 12.6V 20A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery). Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery). Continuous discharge current (upper limit): 20A (if the cooling environment is not good, please reduce the load current use). Continuous...
Reference: RBD-1634
Size: 0.91 inch Resolution: 128 x 32 Controlling Chip: SSD1306 Display Area: 22.384 x 5.584mm Driving Voltage: 3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White
Reference: RBD-1754
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1771
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-1781
1. Micro USB ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 16 x 14 mm .
Reference: RBD-1782
1. USB Type B Female ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 20 x 20 mm .
Reference: RBD-2049
Rotation Angle: 300° ±10° Gyroscopic Moment: 10-200gf.cm Rotational Stopper Strength: 3Kgf.cm Push-Pull Strength: 8kGF Max Shaft Wobble: 0.6xL/20MM p-p Max Total Resistance Tolerance: ±20% Residual Resistance: R less than or equal to 10K Ohms 10 Ohms Withstand Voltage: 1 minute at 300V AC Rotation Life: 10000 times Can be used as a 10K contrast...
Reference: RBD-1783
1. USB Type A Male ( 4pin, A type, Male connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 32 x 15 mm .
Reference: RBD-1784
1. USB2.0 Type A Female ( 4pin, A type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 22 x 17 mm .
Reference: RBD-1785
1. USB3.0 Type A Female ( 9pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 28 x 25 mm .
Reference: RBD-1786
1. USB Type C Female ( 13pin, C type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 40 x 25 mm .
Reference: RBD-1953
Input Voltage:DC 4.5-24V Module Size: 10 x 20 mm Adjustable Range:0.8-17V,fixed voltage (1.8V 2.5V 3.3V 5V 9V 12V) Output Current:3A (max),actual testing input 12V output 1.5A Transform Efficiency:97.5%(max) (6.5 to 5V 0.7A) Switch Frequency:500KHz Output Ripple Wave:20mV (12V to 5V 3A) 20m band width
Reference: RBD-2578
Bright red LED display for clear visibility Common anode configuration for simple wiring Displays a single digit (0-9) 10 pins for easy connection Versatile for various electronic projects
Reference: RBD-2150
Type: Voltage Regulator Operating Temperature: -40-+85 Supply Voltage: 60v Dissipation Power: 10A Package: SMD
Reference: RBD-2173
High current 3A charging board for Type-C USB input Adjustable charging current through resistance adjustment Optional cut-off voltage of 4.2V or 4.35V Efficient working effects with a polymer ternary lithium battery Note: No power indicator or battery protection function included
Reference: RBD-2588
Displays a single digit using bright red LEDs Common cathode configuration for simplified wiring 12 pins for versatile connections Clear visibility and compact size Ideal for various electronic projects
Reference: RBD-2590
Displays a single digit using bright red LEDs Common anode configuration for simplified wiring 12 pins for versatile connections Clear visibility in a compact size Ideal for space-constrained electronic projects
Reference: RBD-2592
Displays a single digit using bright red LEDs Common anode configuration for simplified wiring 10 pins for versatile connections Clear visibility in a compact size Ideal for space-constrained electronic projects
Reference: RBD-2591
Displays two digits using bright red LEDs Common anode configuration for simplified wiring 12 pins for versatile connections Clear visibility in a compact size Ideal for space-constrained electronic projects
Reference: RBD-2593
Displays a single digit using bright red LEDs Common anode configuration for simplified wiring 10 pins for versatile connections Clear visibility in a compact size Ideal for space-constrained electronic projects