Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-2199
Compatible with the Arduino IDE, making it easy for beginners to start using Smaller and cheaper than traditional Arduino boards Powered by a 16.0 MHz microcontroller Fully assembled except for headers, allowing for easy soldering Great for projects where size and cost are a concern Perfect for beginners to jump into electronics Can be used for a variety...
Reference: RBD-1809
Digispark Pro ATtiny167 Micro USB 16MHz
Reference: RBD-0576
Chipboard STM32F103C8T6 On board, SWIM interface and reset button Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V. Power light and the Demo indicator light Leads all the pins and has detailed label for the Pins. Support SWIM debug mode. RoboticsBD
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: RBD-1215
131 powerful instructions – Most Single Clock Cycle Execution 32 x 8 general purpose working registers Fully static operation Up to 20MIPS throughput at 20MHz On-chip 2-cycle multiplier Write/erase cycles: 10,000 flash/100,000 EEPROM Optional boot code section with independent lock bits In system programming by on-chip boot program True read while write...
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-0349
Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...
Reference: RBD-0354
Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD
Reference: RBD-0383
Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference
Reference: RBD-0385
IC Name: MCP23017 Package/Case: DIP-28
Reference: RBD-0410
Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
Reference: RBD-0439
Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-1750
Operating Voltage: 3- 12 VDC Amplification: Adjustable 1.5~1000 times Signal Input Voltage Range: 100µV~300mV Signal Output Range: 100µV~300mV
Reference: RBD-1753
Digital I2S interface with high precision 24-bit dataHigh signal to noise ratio is 61 dBAHigh sensitivity – 26 dBFSStable frequency response from 60 Hz to 15 kHzLow power consumption: low current consumption 1.4 mAHigh PSR: -75 dBFS
Reference: RBD-2065
Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts