Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0335
Features: Simonk Programe, Perfect drive Low voltage, over heat protection, with power on self detection function MCU and BEC with independant regulator, high anti-interference ability Throttle stroke adjustable, compatiable with different receivers, good low speed performance
Reference: RBD-0954
Tell you the real capacity of your battery! LCD display show all info you want Micro-USB powered, charge everywhere at your will Charge all popular Li-ion batteries Unique efficient charge method (TC-CC-CV) with 0.5Ax2.
Reference: RBD-1138
Board Based On AI-Thinker A9 GPRS Module Supports Firmware Upgrade Via Serial Port Operating Voltage: 5v
Reference: RBD-0556
Framework: 12N14P KV: 1400KV LiPO Batteries: 2-3S Max. thrust: 930-940gm Shaft: 3mm Propeller: 9-10″
Reference: RBD-1255
Integrated 0.96″ OLED Micro USB connection Compatible with Arduino Compatible with NodeMCU(Lua for ESP8266) Input Power 5V Compatible for Arduino Compatible with NodeMCU(Lua for ESP8266)A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please...
Reference: RBD-0725
Model: Emax Simon Series Burst Current: 40A (up to 10Sec) Input Voltage(V): up to 16V Constant Current: 30A BEC: 5V /2A Suitable Batteries: 2 ~ 4S
Reference: RBD-0927
Weight: 85 gm. Voltage : 11.1 V. Dimensions : 17 x 34 x 72(mm ). Max Continuous Discharge : 25 C(25 A). Balance Plug : JST-XH. Discharge Plug : XT-60.
Reference: RBD-0928
Voltage : 11.1V Constant Discharge : 30C(10.5A) Max discharge : 25C (10 sec) Dimensions : 74 x 34 x 22 (LxWxH)(mm ) Weight : 87 gm Charge Rate : 1-3C Recommended, 5C Max
Reference: RBD-0929
Weight : 97 gm Voltage: 11.1V Capacity: 1500mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
Reference: RBD-1557
USB communication, no need write code Support PC software automation Double antenna Support quad-band, universal worldwide Support 2G/3G/4G Automatically connect to the network Adaptive frequency
Reference: RBD-1962
ESP32-S2-DevKitM-1 Equipped with ESP32-S2-MINI-1 module Easy interfacing Integrates ESP32-S2FH4 chip. PCB antenna 4 MB SPI flash.
Reference: RBD-1603
USB-TTL converter. Logic Level: 5V. Operating Supply Voltage: 5V. Digital I/O Pins: 14. Analog I/O Pins: 6.
Reference: RBD-0324
Wheelbase: 250mm Material: Full Carbon Fiber Weight: 160 gm The arm has multiple motor mounting holes. Equips vibration-free mounting bracket for FPV camera. RoboticsBD
Reference: RBD-2138
Arduino compatibility Full integration USB-TTL converter 32 Mb flash memory Dual microcontrollersA high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and instead use the recommended cable available here:...
Reference: RBD-0214
FPV Camera Color 480p This Camera Can be used with this Boscam FPV 5.8Ghz AV Transmitter and Receiver for FPV Purpose
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-1087
Uninterruptible Power Supply Mini UPS Modem, Router, CCTV Camera and Lighting 6000mAh 22.2W
Reference: RBD-1259
Model No: XW Power Eagle Lipo 1500mAh 7.4V 2S 25C Lipo Battery (T Plug Connector) Weight: 76 gm. Voltage: 7.4V. Dimensions : 26x34x72 (mm ). Max Continuous Discharge : 25C(25A). Balance Plug: JST-XH. Max Burst Discharge: 90 C (50A). Discharge Plug: T-Plug.
Reference: RBD-0946
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Reference: RBD-1552
Working Frequency: 868 MHz Distance: 8000m RF IC: SX1276
Reference: RBD-1691
Model: Emax SimonK Series. LiPo Battery Input: 2 ~ 3S. Continuous Current: 30A. Burst Current(10S): 40A (for 10Sec). BEC Mode: Linear. BEC Output: 1A/5V.
Reference: RBD-1722
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.
Reference: RBD-2153
Framework: 12N14P KV: 980KV LiPO Batteries: 2-3S Max. thrust: 880gm Shaft: 3mm Propeller: 9-10″
Reference: RBD-2506
The SF Racing F3 flight controller is designed to provide high performance flight experience for the hobbyists. With verified sensor algorithm, it provides incomparable I/O capabilities. The SF Racing F3 runs a next-generation 32-bit STM32F303CCT6 processor, an MPU6500 accelerometer and a gyroscope sensor, all high integrated on a lightweight PCB to...
Reference: RBD-1910
Square onboard USB interface for connection stability The use of imported high-performance USB controller chip Use the special relay driver chip ULN2803, relay work more stable Military grade PCB board production Input voltage: DC 12 V Input Current: more than 300mA Connection : NC / COM / NO Note: Relay might be different from the picture as per stock
Reference: RBD-2507
Reference: RBD-2563
Introducing the FLYWING Brushless ESC, a high-performance electronic speed controller designed for RC airplane models and hobby planes. This ESC offers reliable and top-quality components to enhance the overall performance of your RC aircraft.
Reference: RBD-1945
TTGO module from LilyGO Microcontroller based on an ESP32-S2 chip. USB-C connection MicroSD card adapter.
Reference: RBD-2774
Enhance your DIY RC robot or FPV setup with the FPV Head Tracker Dual Axis Servo Gimbal Bracket. This dual-axis servo gimbal bracket is designed to securely hold your camera in place, allowing for stable and precise positioning during operation. Crafted from lightweight aluminum alloy, this bracket ensures durability without adding unnecessary weight to...
Reference: RBD-1732
Raspberry Pi 4B/3B+/3B U100 UPS HAT Expansion Board Cooling Fan
Reference: RBD-1729
Tuya Smart Universal IR Remote Control your Air Conditioner TV AC Works with Alexa, Google Home