Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-1039
The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-2141
Rating contract (Max.): 10 W Switching power supply (Max.): 110VDC Resistance contract (Max.): 100 Ω Appro. Float Ball Size (mm) : 24×17 (LxD) Body Total Length (mm) : 85 Cable Length (cm) : 37 Total Float opening: 70° Switch ON/OFF angle Approx. betn 15° to 20°
Reference: RBD-0697
Driver Chip: CH340G Supports all basic windows versions. The adapter plate integrated 1000μF solid capacitors to ensure the current supply The power supply will not be a problem to make WIFI module crashes unresponsive. Using 3225 SMD crystal oscillator, improve the stability of serial work, on a beautiful and tall. Working voltage: 4.5V – 5.5V (Onboard...
Reference: RBD-1773
Supply Voltage: 5V USB / 3.7V lithium battery Output Port: 3-wire audio interface/DIY pad Output Type: Analog signal Bluetooth name: VHM-314-V3.0 Bluetooth version: 5.0 Bluetooth passcode: no password Sound source: Bluetooth. USB-PC input(after the back pad is connected, the computer can be connected as a sound card though Micro) Operation method:...
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-2271
Wide compatibility with ESP32-DevKitC(30P) series boards Safe and reliable with stable power and signal transmission Extended GVS interface for easy connection to various electronic modules and sensors JUMP interface for easy reuse of all pins, making it ideal for DIY projects Versatile and reliable option suitable for a wide range of projects
Reference: RBD-2044
Model: ESP32-CAM-MB Color: Black Chipset: CH340G Connectivity Technology: USB Note: The camera module is not included with the board.
Reference: RBD-1336
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...
Reference: RBD-1020
Frequency (MHz) : 824 – 960 MHz & 1710 – 1980 MHz Gain:2 / 3 dBi Impedance (Ω): 50 Connector Type: SMA Plug VSWR :< 2.5
Reference: RBD-1575
Part Number: G3MB-202P Power supply:5VDC/160mA Trigger Voltage (VDC):5 Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-1852
IPEX To SMA Female External Antenna Adapter SMA Male Antenna for 2.4G WIFI Module Only Antenna and Adapter RF Cable ESP32 Cam is not included
Reference: RBD-1641
Product: GSM Antenna Color: Black SMA male straight 5cm 900-1800MHz radio antenna. Frequency: 900MHz – 1800MHz Maximum Power: 50W Length: 5cm/1.97 inch
Reference: RBD-1212
Single crystal 12M Tablet 340 USB port to serial port communication. USB1.1/2.0 compliant solution. Built-in 128 byte TX/512 byte RX buffer. Supports auto-Handshake Protocol. Support Win95/98/98se/ME/2000/XP/win7 32bit 64bit/Vista/supports full speed USB data transfer protocol. Design of electromagnetic interference. Data Exchange application. CH340 USB...
Reference: RBD-1770
Brand new and high quality Included USB transceiver, without external circuit device With 3.3V and 5V dual power output With three LEDs: power indicator, data reception indicator, the data transmission indicator, working status Meets the USB2.0 specification requirements With self-recovery fuse. In the event of the accidental short circuit, it can...
Reference: RBD-2311
USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.
Reference: RBD-2530
DE-9 (DB-9) Female Socket Connector to Terminal Block Breakout
Reference: RBD-2531
DE-9 (DB-9) Male Socket Connector to Terminal Block Breakout
Reference: RBD-2313
Sensing range: 3 – 80cm. Input voltage: 5VDC. Current Consumption: 300mA. Digital Output. Cable length: 1m. Diffuse reflective type.
Reference: RBD-2657
Compact and lightweight design for easy installation and operation, offering a plug-and-play experience. Automatically activates when detecting human body temperature within the sensing area in low-light environments, enabling automated control of connected lamps (with a 45-second time delay). Caution: Avoid using multiple lights in series or parallel and...
Reference: RBD-2892
Model: SNA118 Material: Plastic Plastic Type: PC Tool Supplies: CuttingDoes not Include ESP Wireless Module
Reference: RBD-2309
Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! This module contains an ESP8285, which is an ESP8266 processor with 1MB of FLASH memory already built in. You can use it just like an ESP8266, it's the same processor and WiFi The ESP8266 processor from Espressif is an 80 MHz microcontroller with a...
Reference: RBD-2651
D1 Mini board with 4 MB flash memory and ESP8266 chipset. The board can be programmed with Arduino IDE, has the CH340 USB chipset and allows you to create IoT devices quickly and easily.
Reference: RBD-2652
Firstly, In terms of pins, the D1 Mini and NodeMCU V3 development boards are quite similar. They both break out all ESP8266 ESP-12E/F pins. The NodeMCU V3 board has additional 3V3 and GND pins. Hence, it is more suitable for various connections to devices with an additional button for the flash. A high-quality USB cable is essential for this board to...