Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-1039
The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...
Reference: RBD-1212
Single crystal 12M Tablet 340 USB port to serial port communication. USB1.1/2.0 compliant solution. Built-in 128 byte TX/512 byte RX buffer. Supports auto-Handshake Protocol. Support Win95/98/98se/ME/2000/XP/win7 32bit 64bit/Vista/supports full speed USB data transfer protocol. Design of electromagnetic interference. Data Exchange application. CH340 USB...
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-0353
Driver IC: SSD1306 Support wide voltage: 3.3V-5V DC Communication: IIC Working temperature: -30-80 degrees. RoboticsBD
Reference: RBD-2160
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-2198
Model: CH341 Series Main Chip: CH341B Dimensions in mm (LxWxH): 85 x 28 x 12 Weight (gm): 20 8-bit parallel in EPP or MEM mode
Reference: RBD-2311
USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-2412
Compatible Chips:ATMega Series Tiny Series Classic Series CAN Series PWM Series You can also use this to recover your Arduino Bootloader
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-2413
Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...
Reference: RBD-2416
5V (The max current depends on your USB port, usually 500mA) 3.3V (Using LDO, 300mA MAX) Use CH340G with stable performance. Driver: 1. CH340G USB to UART driver
Reference: RBD-2425
Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.
Reference: RBD-0697
Driver Chip: CH340G Supports all basic windows versions. The adapter plate integrated 1000μF solid capacitors to ensure the current supply The power supply will not be a problem to make WIFI module crashes unresponsive. Using 3225 SMD crystal oscillator, improve the stability of serial work, on a beautiful and tall. Working voltage: 4.5V – 5.5V (Onboard...
Reference: RBD-2427
Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.
Reference: RBD-2463
The SOP8 test clip is made of high-quality plastic and copper metal, which is durable and can be reused.When using the SOP8 test clamp, do not force it down, open the clamp and clamp it in from the left and right sides of the chip.The same is true when disassembling, you can't pull it out directly, you must first separate the clip from left to right, and...
Reference: RBD-0684
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-2044
Model: ESP32-CAM-MB Color: Black Chipset: CH340G Connectivity Technology: USB Note: The camera module is not included with the board.
Reference: RBD-1336
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...
Reference: RBD-1020
Frequency (MHz) : 824 – 960 MHz & 1710 – 1980 MHz Gain:2 / 3 dBi Impedance (Ω): 50 Connector Type: SMA Plug VSWR :< 2.5
Reference: RBD-1852
IPEX To SMA Female External Antenna Adapter SMA Male Antenna for 2.4G WIFI Module Only Antenna and Adapter RF Cable ESP32 Cam is not included
Reference: RBD-1641
Product: GSM Antenna Color: Black SMA male straight 5cm 900-1800MHz radio antenna. Frequency: 900MHz – 1800MHz Maximum Power: 50W Length: 5cm/1.97 inch
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-0980
Dimensions : 66 x 66 x 3 mm. Weight : 25 gm. Supply Voltage : 5 VDC. Interface : IO . 8 x 8 = 64 RGB. Chip : WS2812.
Reference: RBD-0981
Low power device. DTMF decoder chip. Band-split filter. Digital decoding functions. Modem interfaces. Mobile radios.