Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-2045
Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-0684
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
Reference: RBD-0742
Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
Reference: RBD-1678
2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module
Reference: RBD-2158
Driver Chip: TB6560AHQ Operating Voltage: 10-35V Nominal Voltage: 24V With the large heat sink to ensure good heat dissipation 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
Reference: RBD-1762
Input voltage(V): 9-12 It can produce high-temperature PCB board size(cm): 3.1 x 4 It is convenient for fans to install high efficiency Weight(g): 20This product is shipped as unassembled and requires soldering to be completed. You will need to do the soldering yourself.
Reference: RBD-2111
DC Motor Speed Controller PWM 12V Controls the speed of a DC motor using Pulse-Width-Modulation (PWM) Provides continuous current of 3A to the motor or DC load Includes a 3A fuse for protection Supports reverse connection of power supply
Reference: RBD-1809
Digispark Pro ATtiny167 Micro USB 16MHz
Reference: RBD-2389
This module is ideally suited to motor control to your project. This is the L298N Dual H-Bridge module which allows you to build in 2 controlled motors to your projects, controlling the speed with current. This can be used with a wide range of microcontrollers including Arduino and Raspberry Pi.
Reference: RBD-2676
Suitable for use with a wide range of stepper motors and drivers. Can be integrated into a simple control platform with a stepper motor and DC power supply. Offers three selectable low-frequency signal options: high (5.4k-160kHz), middle (540-16.6kHz), and low (80-2.4kHz), adjustable via jumper settings. Capable of producing both pulse and PWM signals,...
Reference: RBD-2112
Single side PCB. Reinforced with glass fiber laminate on the core. 250 x 380 x 1.5 mm. Ideal for prototyping. Imported from China Color: Pale Green Smooth Machine Cut
Reference: RBD-2113
Single side PCB. Reinforced with glass fiber laminate on the core. 215 x 330 x 1.4 mm. Ideal for prototyping. Color: Ash, White Smooth Machine Cut
Reference: RBD-2131
ESP32-S2 based WIFI development board Features S2FN4R2 WIFI IC Equipped with 4MB FLASH and 2MB PSRAM Type-C USB connectivity 27 digital input/output pins with support for interrupt/pwm/I2C/single wire ADC, DAC, I2C, SPI, UART, USB OTG
Reference: RBD-1663
Brand: RoboticsBD
Distribution strip, Tie-point 200 Terminal Strip, Tie-point 630 Completely reusable Breadboard Brand new & high quality Breadboard power supply module, compatible with 5 V, 3.3 V 140pcs Solderless Breadboard Jumper Cable Lead Kit Hard Wire with Angled shape
Reference: RBD-2266
Versatile and powerful development board for IoT and embedded systems projects. USB Type-C port for reversible plug orientation and easy connection to computer or other devices. Built-in Wi-Fi and Bluetooth module for wireless connectivity. Arduino IDE compatibility for easy code writing and uploading. Suitable for a wide range of applications, including...
Reference: RBD-2662
BlackPill version 3.1 board equipped with STM32F411CEU6 microcontroller, USB type C connector, additional user programmable button, LED, built-in RTC clock, 16-channel A/D converter. It has 512 kB of Flash memory and 128 kB of SRAM memory. Popular SPI, I2C, USART and SDIO interfaces are also available. Included with the board are 2 20-pin goldpin strips...
Reference: RBD-2679
STM32F103C8T6 ARM Development Board Module with Type-C Interface and Enhanced Memory Enhance your embedded system projects with the STM32F103C8T6 ARM development board module. Featuring a Type-C interface for easy connectivity, this module offers seamless one-click download capability. With an upgraded BOOT switch, you can easily perform upgrades without...
Reference: RBD-2690
Single side PCB. Reinforced with glass fiber laminate on the core. 330 x 200 x 1.4 mm. Ideal for prototyping. Color: Copper, White Smooth Machine Cut
Reference: RBD-2831
Introducing a compatible Raspberry Pi Pico Clone, Made in China. Equipped with the authentic Raspberry Pi RP2040 microcontroller chip, this Pico offers comparable performance at a competitive price point. However, it's essential to note that while the microcontroller chip is genuine, the PCB itself is not manufactured by Raspberry Pi but rather in China....