Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-0376
Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: RBD-0435
Supply Voltage : 8-35 VDC. Current : 1.0A (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0662
Power supply: 7V to 30V. The higher the voltage, the higher the torque at high speeds. Adjustable current control from 150mA/phase to 750mA/phase. Logic voltage: 5V or 3.3V. A3967 microstepping driver. RoboticsBD
Reference: RBD-1724
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
Reference: RBD-1810
Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver
Reference: RBD-0696
Voltage : Input through (USB) DC 5V Output via (DC Round Pin) : DC 12V Color: BLACK Input / Output Current: Maximum Input 0.6 Easier for installation save time and money Easy to use.
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-0963
Current and voltage display in turn, easy and comfortable to use. Small and portable, do not need other power supply. Measuring range: DC 3V – 9V / 0 – 3A (up to 5A ) Portable Device Interface: USB2.0, USB3.0 Product Weight: 0.025 kg Two output ports
Reference: RBD-0983
Capacity (mAh): 960-2000 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life SMALL SUN
Reference: RBD-1019
Charging Voltage: 12.6V-13V Overcharge Voltage Range: 4.25V-4.35V ± 0.05V Overpressure Voltage Range: 2.3V-3.0V ± 0.05V Upper Limit Operating Current: 5A-6A
Reference: RBD-1334
Charging current: 1A (maximum) Maximum charging voltage: 4.2V (1.5% accuracy) Input voltage: 4.5V-5.5V
Reference: RBD-1343
Compatible With: AA, AAA, 9V Battery red light show the charging situation 9V Battery Charger
Reference: RBD-1242
6-piece Acrylic case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble without any Screws or Nut-Bolts Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel Mounting holes and anti-slip rubber feet at the back.
Reference: RBD-1371
Input: AC 100-240V/ 47-63HZ Output: DC 3.7V/ 500mA Termination voltage: 4.2V+-1%
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-0563
Overcharging and Over Discharging Protection Short circuit protection: Yes Applicable assembly: Nominal 4.5V Batteries / 3 strings. RoboticsBD
Reference: RBD-0110
রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক। আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা 5V,3A. আমরা আমাদের টেস্ট এ 5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন। এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...
Reference: RBD-1421
3S 11.1V 12.6V 20A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery). Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery). Continuous discharge current (upper limit): 20A (if the cooling environment is not good, please reduce the load current use). Continuous...
Reference: RBD-1420
Over Charge Voltage Range: 4.25-4.35 V + 0.05 V Over Voltage Range: 2.5-3.0 V + 0.05 V Max. Operating Current: 13 A Max. Limiting Current: 20 A Charging Voltage: 8.4-9 V
Reference: RBD-1702
Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-1067
Length: 1.0M Diameter: 3 mm. Color: Black Material: PE/PVC/ABS Micro-USB
Reference: RBD-1528
Input: 1S-8S Battery Battery type: Lipo/LiFe/Li-ion/LiMn It has a Buzzer Alarm for low voltage indication. Useful for measuring each cell voltage. Cell Voltage Display Range: 0.5v-4.5v Total Voltage Display Range: 3.7-36v Alarm set values: Off or 2.7-3.8v
Reference: RBD-1933
Length: 1M Diameter: 3 mm. Color: Black Material: PE/PVC/ABS
Reference: RBD-1156
Brand: Raspberry Pi Official
FPC (Flexible Printed Circuit) cable. Length: 16cm. Ways: 15-way. Pitch: From 0.5mm(Raspberry Pi Zero) to 1.0mm (Raspberry Pi Camera and Raspberry Pi 3). Compatible with 5MP Raspberry Pi Zero W Camera.
Reference: RBD-0945
Length: 1.5m Weight: 82 gm. Color: Steel Black Supports all HDTV devices including 1.4 Supports resolution up to 1080P Supports 3D and Blu-ray Disc
Reference: RBD-1623
Noiseless Performance Very low Current consumption Easy to install and connect.
Reference: RBD-1060
Perfectly fit on the extruder Noiseless Performance Very low Current consumption Easy to install and connect.
Reference: RBD-1694
Capacity (mAh): 960-2000 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life Genuine SMALL SUN
Reference: RBD-1368
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)