Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-0716
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.
Reference: RBD-0578
The degree of Freedom (DOF): 2 Paw material: aluminum alloy. RoboticsBD Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm
Reference: RBD-0259
Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY. This car is the tachometer encoder. With a 4 AA battery box (batteries not included). It can be used for distance measurement, velocity. Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, Wireless remote control....
Reference: RBD-0212
Input: 110v or 240v A/C (50/60Hz) Cell Count: 2~3s Battery Type: LiPoly Output Current: 3 x 800mA
Reference: RBD-0684
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
Reference: RBD-0749
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim
Reference: RBD-0430
Operating voltage: 4.5V to 5.0 V Output format: 8 Analog and Digital voltages. Optimal sensing distance: 0.125″ (3 mm). RoboticsBD
Reference: RBD-0742
Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
Reference: RBD-1678
2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0696
Voltage : Input through (USB) DC 5V Output via (DC Round Pin) : DC 12V Color: BLACK Input / Output Current: Maximum Input 0.6 Easier for installation save time and money Easy to use.
Reference: RBD-0494
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: STD-120200
Reference: RBD-2158
Driver Chip: TB6560AHQ Operating Voltage: 10-35V Nominal Voltage: 24V With the large heat sink to ensure good heat dissipation 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
Reference: RBD-2111
DC Motor Speed Controller PWM 12V Controls the speed of a DC motor using Pulse-Width-Modulation (PWM) Provides continuous current of 3A to the motor or DC load Includes a 3A fuse for protection Supports reverse connection of power supply
Reference: RBD-2389
This module is ideally suited to motor control to your project. This is the L298N Dual H-Bridge module which allows you to build in 2 controlled motors to your projects, controlling the speed with current. This can be used with a wide range of microcontrollers including Arduino and Raspberry Pi.
Reference: RBD-1213
Battery Charger for 2*18650 Rechargeable Li-Ion Batteries Suitable for 2*18650 rechargeable Li-Ion batteries Input: AC 100-240V/50-60Hz 200mA max Output: DC 4.2V 1000mA*2
Reference: RBD-2676
Suitable for use with a wide range of stepper motors and drivers. Can be integrated into a simple control platform with a stepper motor and DC power supply. Offers three selectable low-frequency signal options: high (5.4k-160kHz), middle (540-16.6kHz), and low (80-2.4kHz), adjustable via jumper settings. Capable of producing both pulse and PWM signals,...
Reference: RBD-1073
3.7V 600mAh 25C Lipo battery Product Type: Lithium Polymer Battery Pack The LiPo battery has matched resistance. Good Temperature Control. Minimum weight in Class
Reference: RBD-1319
High Quality Extra power Rechargeable Must be Charged after purchase Constant 9V Output till lasts Metal Jacket Body Good Built Quality and hence Leakproof Easy to install and Replace Corrosion free Connector Point for long-term use 0% Mercury and Cadmium. Environment-friendly OEM Compatible. *** New Batteries must be charged before use.
Reference: RBD-0159
Provides a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 6 keys select, up, right, down, left and reset. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage...
Reference: RBD-1419
Model: 6S 15A 18650 Lithium Battery Protection Board Balanced charge: None Short circuit protection: Yes
Reference: RBD-0032
USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...
Reference: RBD-1474
This Lithium ion battery protection PCB protect single Lithium ion batteries. 20A continous current. Suitable for electric drills,motors,or aircraft models which require heavy current load.
Reference: RBD-0227
Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm
Reference: RBD-1559
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1560
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1674
Xtar MC1 charger Output current :500-50mA Universal Charger for : Charge for :10440/ 14500/ 14650/ 16340/ 17500/ 17670/ 18350/ 18500/ 18650/ 18700/ 22650/ 25500/ 26650 3.6/3.7V rechargeable Li-ion battery With package box
Reference: RBD-1718
Model: BT-168 PRO Product Name: Digital Battery Tester Type: Pointer Voltage Measurement Rated Voltage: 9V Measurement Accuracy:0.1V
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0282
Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU