Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0406
Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum. RoboticsBD
Reference: RBD-0730
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Reference: RBD-2063
Compatible with all embedded systems platforms. Supports field updates and troubleshooting. Pins: 10. Cable length: 200mm. Cable size: 28 AWG.
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1771
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-1785
1. USB3.0 Type A Female ( 9pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 28 x 25 mm .
Reference: RBD-1918
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-1855
Input voltage: 3-40V Output voltage: 1.5-35V(Adjustable) Output current: Rated current is 2A, maximum 3A Switching Frequency: 150KHz Operating temperature:Industrial grade (-40 to +85 ) Conversion efficiency: 92%(highest)
Reference: RBD-1703
Excellent Grip and Better Cap Design Shock Resistance and Light Weight Easy Pocket-Friendly An electrician as well as Electronics useful tool
Reference: RBD-1704
Metal Scalpel Hobby Cutter Engraving Crafting Tool 6 Blades
Reference: RBD-1892
Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-2185
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm front and rear(approx.) Weight; 19g (approx.)
Reference: RBD-1953
Input Voltage:DC 4.5-24V Module Size: 10 x 20 mm Adjustable Range:0.8-17V,fixed voltage (1.8V 2.5V 3.3V 5V 9V 12V) Output Current:3A (max),actual testing input 12V output 1.5A Transform Efficiency:97.5%(max) (6.5 to 5V 0.7A) Switch Frequency:500KHz Output Ripple Wave:20mV (12V to 5V 3A) 20m band width
Reference: RBD-2190
Operating Voltage: 1.5 to 3VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 5mm (approx.) Weight; 22.5g (approx.)
Reference: RBD-1957
Input Voltage: 12V Connector: 5.5mm DC Jack Output power on/off switch Two-row multiple pin outputs, easy to use and connect Outputs 3.3V DC at 800mA maximum current Outputs 5.0V DC at 800mA maximum current Outputs 12V DC (the 12V output is directly connected to the input, i.e. with 12VDC input, this output will be 12VDC; with 9VDC input, this output will...
Reference: RBD-1798
Diameter 5mm and Length 30 (M5 x 30) Phillips Flat Head Machine Screw (Countersunk) Stainless Steel
Reference: RBD-2519
Small 1.5 – 3V DC motor with fan for science projects or general experimenting 3V DC motor with cable Soft 3-leaf fan bladeThe Jumper may become detached during shipping and require soldering with a soldering iron.
Reference: RBD-2457
Regulates 4.5 – 40V input to a 1.25 – 37V output @ up to 1.5A
Reference: RBD-1940
Soldering Stand Size : 10 x 6.7 x 10 cm(LxWxH). Weight: 105gm. Nickel-plated wide spring holder Robust and powerful base to uphold the weight of soldering irons varying from 30w, 35w, 40w, 50w, 60w and 75w
Reference: RBD-2859
Small metal vibrating motor powered by 3 V. Idle current 90 mA. Dimensions: 9 x 5.2 x 5.2 mm.
Reference: RBD-2653
2.8V-5.5V to ±12V DC Conversion Step Up Power Supply Module is straightforward. There is a 2.8 to 5.5 V DC input and the module outputs +12 V and -12 V DC dual power supply voltage with a current rating of a maximum 30 mA. Off course the current output is low but sometimes it suits in many situations where one is looking forward for a small boost...
Reference: RBD-2726
2A 5V Charge Discharge Integrated Module 3.7V 4.2V for 18650 Lithium Battery Charging Boost Mobile Power Supply Charge and Discharge Protection Converter Protection PCB Board Module