Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0227
Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0432
Iron Body Material High quality ultra-compact electric lock. RoboticsBD Rustproof, durable, safe, convenient to use. Suction which tightly sucks the iron, thus locking the door. Designed with the open frame type and mount board, high power. Easy to install for the electric door lock or other automatic door lock systems with the mounting board Applicable...
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-0343
Model number: TEC1-12706 Operating Voltage: 12V Maximum Voltage Umax (V) : 15.4V Maximum Current Imax (A) : 6A Maximum Power: 92 W Maximum Temperature: 138°C Power Cord: 200mm.RoboticsBD
Reference: RBD-0950
Model : RS-360 micro-motors small pump Operating voltage : 4V-12V Current : 0.8A Motor diameter : 27 mm Pump Length : 52 mm Out of the water hole diameter : 4 mm Weight : 70g
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-0951
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-0349
Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...
Reference: RBD-0350
100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1114
N20 Micro Gear 12V 100RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel
Reference: RBD-1257
Simple Plug and Play operation. USB input Plug It Can operate on any 5V DC power supply like Power bank 1 Meter cable with DC jack provides the convenience to connect and disconnect project easily
Reference: RBD-1340
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1341
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1346
Model: SG92R Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 2.5kg-cm
Reference: RBD-1165
9 Layer Acrylic stylish case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0278
Model: MG995 Weight: 55 gm Operating voltage: 4.8V~ 7.2V Servo Plug: JR Stall torque @4.8V : 10 kg-cm Stall torque @6.6V : 12 kg-cm
Reference: RBD-0410
Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
Reference: RBD-1234
Easy two-piece installation design Hole for mounting the pi inside the case Rubber pad grip at the bottom Precise access to all port and status LEDs with Symbols Raspberry LOGO on Top
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-1242
6-piece Acrylic case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble without any Screws or Nut-Bolts Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel Mounting holes and anti-slip rubber feet at the back.
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-1309
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin EU type. Output Plug: Micro USB Plug. Compatible with: Raspberry Pi B+, 2, 2B, 2B+,3 ,3B+, Zero, Zero W. It has a switch so you can easily power off the device without having to unplug it right from the socket.
Reference: RBD-0110
রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক। আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা 5V,3A. আমরা আমাদের টেস্ট এ 5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন। এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...
Reference: RBD-1702
Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-0729
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-1144
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin Type A Japan Output Plug: Type C
Reference: RBD-1156
Brand: Raspberry Pi Official
FPC (Flexible Printed Circuit) cable. Length: 16cm. Ways: 15-way. Pitch: From 0.5mm(Raspberry Pi Zero) to 1.0mm (Raspberry Pi Camera and Raspberry Pi 3). Compatible with 5MP Raspberry Pi Zero W Camera.