Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0335
Features: Simonk Programe, Perfect drive Low voltage, over heat protection, with power on self detection function MCU and BEC with independant regulator, high anti-interference ability Throttle stroke adjustable, compatiable with different receivers, good low speed performance
Reference: RBD-0042
Latest 6-axis flight control system with adjustable gyro sensitivity Permits super stable flight Lightweight airframe with nice durability
Reference: RBD-0378
Model: Eachine 1000TVL 1/3 CCD Lux: 0.08Lux/ F1.2 Sensor: 1/3 “CCD Format: NTSC/PAL(Free switch) Resolution: a.Ultra High Definition 1000TVL b.PAL: 976H X 582V c.NTSC: 976H X 494V Lens: 2.8mm IR coated. RoboticsBD FOV: 110 °
Reference: RBD-0380
Eachine VR D2 40CH 5 Inches 800 x 480 Raceband 5.8G Diversity FPV Goggles with DVR Lens Adjustable
Reference: RBD-1733
Brand: Creality Official
Built-in WIFI function: Remote control printing anytime, anywhere; A Bit More Intelligence Ultra-silent Design: 32 Bit Mute Board and Mute Fan Design; Intelligent Auto-leveling: V2.0 Auto leveling way, is the same with CR-6 SE. Screen Protection & Auto-shutdown;. Safe and worry-free save energy and power. 6-steps to assemble 8 minutes to complete,...
Reference: 1403
Brand: Creality Official
Replaced with New Version Creality Ender-3 V3 SE 3D Printer. Click Here
Reference: 1404
Brand: Creality Official
Modeling Technology: FDM(Fused Deposition Modeling) File Formats: STL/OBJ/AMF Slicer Software: Creality Slicer/Cura/Reptier-Host/Simplify3D Print Speed: 80-100mm/s Resume Print Function: Yes Printing Size: 235x235x250mm
Reference: 1375
Brand: Anycubic
Technique: LCD-based SLA Printing Speed: 30mm(H)/hour Power: 30W
Reference: 1316
Tougher and stronger Less warping (about 0.4% compared to over 8% in regular ABS) Prints smoother & smoother printed objects Better scratch, heat and oil resistance Can be polished using acetone Can be easily colored.
Reference: RBD-0167
(Retired) Description: RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-20LA, a very simple to use RFID reader module from ID Innovations. With a built in antenna, the only holdup is the 2mm pin spacing....
Reference: RBD-0660
Material: glass fiber Can connect 1-4 ESC. RoboticsBD This has an XT60 plug to connect a battery.
Reference: RBD-1315
Great bio-compatibility, excellent transparency and environment-friendly Low shrinkage, good round shape Accurate diameter (±0.02mm) Easy to print with stable printing performance Various colors are available 100% bio-degradable and FDA food safety approved
Reference: RBD-0704
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
Reference: 1391
TPU rubber based Material. Very flexible and elastic. Shore A Hardness at 87A. Tensile Strength 52 MPa.
Reference: 1392
PETG Filament Plastic For 3D Printer 1.75mm1KG/Roll Compatible with Anycubic, Creality. Temperature: 205-230 °C Bed Temperature: 60-80 °C
Reference: 1317
TPU rubber based Material. Very flexible and elastic. Shore A Hardness at 87A. Tensile Strength 52 MPa.
Reference: RBD-1386
Brand: Anycubic
Wavelength(nm): 395-405 Color: Black Density(g/m^3): 1.08-1.13 Hardness(Shore D):79.0 Tensile Strength(MPa): 46-67 Elongation at Break(%):28-35
Reference: RBD-0186
(Retired) WiDo - Arduino WIFI IoT(Internet Of Things) Node (Arduino Compatible) Wido is an Arduino compatible WIFI IoT Node development board, which integrates with WG1300 WIFI solution. The microcontroller of Wido is ATMEL ATmega32U4.
Reference: RBD-0735
Supply Voltage: 7V. Processor: 32 Bit Cortex M4 Core Bus interface (UART, I2C, SPI, CAN). Firmware: Mission planner. Sensors: Gyrometer, Accelerometer, Barometer & Magnetometer Micro SD card to record flight data. RoboticsBD
Reference: RBD-0211
(Retired) The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,
Reference: RBD-0824
Material: glass fiber Can connect 1-4 ESC. This has an T connector plug to connect a battery.
Reference: RBD-1369
Lifetime: 30 million Rated voltage:125V Rated current: 5A Dissipation Power: IC Supply voltage: IC KW11-3Z bearing microswitch.
Reference: RBD-0214
FPV Camera Color 480p This Camera Can be used with this Boscam FPV 5.8Ghz AV Transmitter and Receiver for FPV Purpose
Reference: RBD-1312
XY plotter robot kit is a drawing robot Supports Pen and Pencil Supports Laser Engraving
Reference: RBD-0029
The first-generation Raspberry Pi Model B was released in February 2012 SOC BCM2835 Memory 256 MB Standard Form Factor Ethernet available. Wireless (Wifi/Bluetooth) not available. GPIO 26 pin
Reference: RBD-1311
mDrawBot is a 4-in-1 drawing robot kit it can be assembled into 4 different drawing robots: mScara. mCar. mSpider. mEggBot.
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-1752
Ortur Laser Master 2 Model: Ortur OLM2-LU1-4 20W Year: 2021 Engrave Area: 400mm x 430m Available Laser Modules: 20W Model – Laser Power: 5000-5500 MW Laser Engraver and Cutter Kit
Reference: 1265
Brand: Anycubic
Large build volume: 210 x 210 x 205 mm User-friendly 3.5-inch touch-screen interface Can be assembled in just a few minutes Full Rigid Solid metal frame construction and superior stability High quality Ultrabase
Reference: RBD-0013
Arduino Programming Supports fuses and lock bit programming Upgradeable for future device support Supports target voltages from 1.8V to 5.5V Adjustable ISP programming speed (50Hz to 8MHz SCK frequency) USB 2.0 compliant (full speed, 12Mbps) Powered from USB, does not require external power supply Target interface protection Short-circuit protection...
Reference: 1113
Brand: Anycubic
Large build volume: 210 x 210 x 205 mm User-friendly 3.5-inch touch-screen interface Can be assembled in just a few minutes Full Rigid Solid metal frame construction and superior stability High quality Ultrabase