Reference: RBD-1219

3.5inch LCD Display Shield for Arduino

2 reviews

Supports development boards such as Arduino UNO and Mega2560 for plug-in use without wiring 480X320 resolution, clear display Support 16-bit RGB 65K color display, display rich colors 8-bit parallel bus, faster than serial SPI refresh On-board 5V/3.3V level shifting IC, compatible with 5V/3.3V operating voltage Easy to expand the experiment with SD card...

Reference: RBD-1250

37GB 12V High Torque Gear Motor - 195 RPM

2 reviews

DC 12V 195 RPM 37GB-545 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-0268

Brand: RoboticsBD

3D Printed Robotics claw with servo motor

Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R

Reference: RBD-1357

37GB 12V High Torque Gear Motor - 300 RPM

1 review

DC 12V 300 RPM 37GB-555 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-1390

Nema 17 Stepper Motor 17HS4401S

4 reviews

Nema17 Bipolar. Number of Phases: 2. Step Angle: 1.8°. Phase Voltage: 2.6Vdc. Phase Current: 1.7A. Resistance: 1.5Ω ±10%. Inductance: 2.8mH ±20% (1KHz). Number of Wire: 4 (100cm Length). Holding Torque: 43N.cm. Shaft Diameter: Ø5mm. Motor Length: 40mm. Mass: 270g.

Reference: RBD-0169

Flex Sensor 2.2"

7 reviews

Flex length: 5.6 cm. Total Length: 2.2″ (7 cm). Life Cycle : >1 million. Height : 0.43mm (0.017″), Flat Resistance: 10K Ohms ±30%. Power Rating: 0.5 Watts.

Reference: RBD-1682

37GB 12V High Torque Gear Motor - 100 RPM

2 reviews

DC 12V 100 RPM 37GB-550 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-1759

Brand: Waveshare

E-Ink Electronic E-paper Display Screen Module 200x200, 1.54inch

Display Resolution: 200 x 200 Display Screen Color: Black and White No backlight so keeps displaying last content for a long time even when the power is down Ultra low power consumption, basically power is only required for refreshing SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.

Reference: RBD-1849

775 DC 12V 18000RPM Ball Bearing Large Torque High Power Low Noise DC Motor Original (Imported)

2 reviews

High torque and low noise. Great replacement for the rusty or damaged DC gear motor on the machine. Ball bearing, with the cooling fan. Used in electric tool motors, power is very large, you can make a small spindle motor, and is also suitable for DIY aspects. Used for the electronic game machines, electronic toys, car toys, robots, 

Reference: RBD-0208

Off-Road Wheels - 130x60mm (Pair)

3 reviews

"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."

Reference: RBD-1868

DC 12V 60W High Pressure Micro Diaphragm Water Pump Automatic Switch 5L/min Range 8m Water Pump

1 review

Watering configuration: much the same, additional sprinklers and timers are required 12V DC reflux diaphragm pump 550, the price is the price of a pump, without other accessories Maximum pressure: 0.8MP. Voltage: 12V, current: at least 2A, measured 1A is not able to bring Suction: 3 meters or so, preferably 2 meters (no problem if the vertical height is...

Reference: RBD-0267

Big Easy Driver - Stepper Motor Driver

1 review

Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...

Reference: RBD-2455

2.42" Inch OLED Display SSD1309 12864 SPI Serial Port For Arduino C51 White

2 reviews

2.42" Inch OLED Display SSD1309 12864 SPI Serial Port For Arduino C51 WhiteBrand: No BrandMetal Bracket to protect Display

Reference: RBD-2250

JGY-370 DC 12V 160RPM Self-locking Reduction Worm Gear Motor

JGY-370 DC 12V 160RPM Self-locking Reduction Worm Gear Motor

Reference: RBD-2277

37GB 12V High Torque Gear Motor - 400 RPM

DC 12V 400 RPM 37GB-555 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-2067

7-70V 30A PWM DC Motor Speed Controller Switch with 30 Amp Fuse

7-70V 30A PWM DC Motor Speed Controller Switch Wide voltage input range: 7-70V Maximum output current: 30A Speed control knob with switch function Adjustable potentiometer with flexible cable (15cm length) Includes a 30A fuse for motor interface protection Input power must be 1.5 times greater than the motor's rated power

Reference: RBD-2524

37GB 12V High Torque Gear Motor - 200 RPM

DC 12V 200 RPM 37GB-555 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-2920

2.42 inch OLED Screen LCD Display Module 128x64 SSD1309 SPI 7Pin White

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: SPI (default) Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2921

2.42 inch OLED Screen LCD Display Module 128x64 SSD1309 SPI 7Pin Yellow

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: SPI (default) Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2922

2.42 inch OLED Screen LCD Display Module 128x64 IIC I2C 4Pin White

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: I2C Communication Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2923

2.42 inch OLED Screen LCD Display Module 128x64 IIC I2C 4Pin Yellow

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: I2C Communication Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2803

NEMA17 42BYGH40 2-Phase 4-Wire Stepper Motor for 3D Printers

This is NEMA17 stepper motor commonly used in 3D printers, CNC machines, and linear gantry systems.

Reference: RBD-2897

37GB 12V High Torque Gear Motor - 500 RPM

DC 12V 500 RPM 37GB-550 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-0394

Slip Ring - 6 Wire (1.5A) max 240V

They are very useful for connecting components to wires. It is insulation covered clips connected to the wire from both ends. RoboticsBD

Reference: RBD-0692

4-20MA -50~150℃ RTD PT1000 SBW Temperature Sensor Transmitter Module

Accuracy: +/- 0.2F.S Temperature coefficient: Less than 150ppm/K F.S. Working temperature: 0-100℃ Working humidity: Less than 98% RH

Reference: RBD-0417

Force Sensor Resistor Square 38.1mm

3 reviews

Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD

Reference: RBD-1241

Mecanum Wheel 80mm for Advanced Robotics (Left + Right) Pair

4 reviews

Color: Black Weight: 120g (each) Outer wheel diameter: 80mm Thickness: 37mm 1 pcs Left and 1 pcs Right Wheel No Connecting Hubs

Reference: RBD-1601

Smart Robot Chassis Kit Black 2WD

1 review

Smart Robot Chassis  Black 2WD DC Motor x2 Comes as a kit  Two Wheels Smart Car Chassis Tracking Best for Obstacle Avoidance Robot

Reference: RBD-2321

Red 2WD Aluminum Smart Robot Car Chassis Kit

Drive: 2WD Frame:1.5mm aluminum alloy structure, lightweight and high strength Working voltage: 4.5~6V Wheel Diameter:60mm

Reference: RBD-1155

3.6V Micro Hydro Generator

Built-in Lipo Charging Circuit Stabilized Voltage Output High Battery Capacity

Reference: RBD-2513

5V Electromagnet - 25 Kg Holding Force - P40/20

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 25 Kg / 55 lb Approximate Pickup Weight: 5 KgEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and...

Reference: RBD-2533

QTR-8A Reflectance Sensor Array

2 reviews

This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate analog voltage output.Note:...