- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial IC
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Adapter
- PLC Programming Cable
- Tools, Hardware & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
3D Printed Robotics claw with servo motor
Material: PLA (3D Printed)
Claw max angle: 55mm
Width: 98mm (streched)
Color: Golden, Blue, Red
Servo Motor: MG996R
Store Pickup Available!
Free Ship Over 5000 BDT
Soldering is required
Description knock sensor module and a digital interface, built-in LED build a simple circuit to produce percussion flasher.Interface comes with digital LED, will knock sensor connected digital 3 interface, when percussion sensor senses measure to percussive signals, LED flashing light.
Description: Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers.This smaller solenoid is designed to work directly with 5V~6V which makes it a great match for embedded projects. It has a throw of about 4.5mm and 2 M2 mounting holes on the body.
Weighing Sensor 24 Bit HX711 Dual-Channel Precision A/D Module Pressure Sensor. This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier.
01S Vibration Sensor Module vibration Analog Output Sensitivity LM393Size: 41 * 15 * 12.5mm The main chip: LM393, vibrating probe Operating voltage: DC 3-5V Main features: Has a signal output instructions; With analog and TTL-level signal output signal; Output valid signal is high, the light goes out; Adjustable sensitivity (fine-tuning); Vibration...
Specifications:- Gain: 2.0dBi-2.5dBi- Standing-wave ratio (SWR): <1.5- Directivity: Omni-directional- Center frequency: 5.8Ghz- Connector: RP-SMA- Diameter of connector: 7.67mm- Length:Transmitter antenna:71mm- Receiver antenna:91mm- Net weight: 12g（Tx/Rx）- Package weight:69 g
Dust Sensor, A simple Air Monitor Overview Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cigarette smoke Low power consumption, analog voltage output, the output level is linear with dust density Embedded voltage boost circuit to support wide range of power supply
Mini 2-Axis platform for camera Weight: 20gsuitable for 9g-12g servos or MG90, MG90S, SG90precision and great appearanceit’s a very stable platform for camera Note no servo is included
VGA OV7670 CMOS Camera Module Lens CMOS 640X480 SCCB W/ I2C Interface Arduino
Can be used with: http://store.roboticsbd.com/robotics-parts/265-thermal-printer-sparkfun-robotics-bangladesh.html Description: This is a 34' roll of thermal printing paper for use with our thermal printer. This roll is smaller than you find at most office supply stores so it fits directly into the printer without having to remove any paper from the roll.
Specification: Input voltage range：4～38VDC(Note:input voltage not exceeding 38V) Output voltage range：1.25-36VDC adjustable Output current: 0-5A, recommended for use in 4.5A. Output power: 75W Working temperature: -40~+85 degrees Operating frequency: 180KHz Efficiency:96%（max) Short circuit protection: yes(limit current 8A).
Description: This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board...
12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 54 Torque: 40KG.CM
You can use LC Metal detector non-contact metal induction detection module as a metal detector. When it approaches any metal, it makes a sound. This is a module specifically designed to detect metal. The module operates by inducing currents in metal objects and responding when it occurs. A nice onboard buzzer signals when it detects something and an...
Specification: Module Name: MF522-ED Working current：13—26mA/ DC 3.3V Standby current：10-13mA/DC 3.3V sleeping current：<80uA peak current：<30mA Working frequency：13.56MHz Card reading distance ：0～60mm（mifare1 card） Protocol：SPI data communication speed：Maximum 10Mbit/s
18 DOF Aluminium Metal Hexapod Robot Spider Six Foot/Feet Robotic Frame/Chassis Kit
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they’re usually unreliable or difficult to implement. Well not anymore! We’ve found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
3S 11.1V 12.6V 25A W/Balance 18650 Li-ion Lithium Battery PCB Protection Board Specification: Brand newSize: about 56mm*45mm*1.2mmOver voltage range: 4.25-4.35v±0.05vOver discharge voltage range: 2.3-3.0v±0.05vMaximum operating current: 0-25AMaximum transient current: 34-40AQuiescent current: less than 30uA
TSL2561 Luminosity & Infrared Light integrating sensor