Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0391
Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD
Reference: RBD-0423
Detecting range: >120 degree Analog and digital outputs On-board potentiometer and indicators 1% resistors to make this module more reliable and precise Operating Voltage: 3.3V – 9V Board Diameter: 40 mm.
Reference: RBD-0425
Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD
Reference: RBD-0426
Power supply voltage of 2.5 V ~ 5 V Low power consumption Wide detection range: 240 nm to 370 nm Wide Angle: 130 degrees Schottky type photosensitive diode Good linear response High sensitivity
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-0350
100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.
Reference: RBD-0680
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules. RoboticsBD
Reference: RBD-0923
Measuring range: temperature -40-80 ℃; humidity 0; 99.9%RH Measurement accuracy (25℃): temperature: + 0.5; humidity: + 2%RH (10; 90%RH) Resolution: temperature: 0.1 ℃, humidity: 0.1%RH Attenuation value: temperature: <1℃ / year; humidity: < 1%RH/ years High precision Capacitive type Full range temperature compensated Relative humidity and...
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-0569
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-1559
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1560
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1946
Comes with the BME280 sensor. Pressure accuracy of ±1 hPa. Temperature accuracy ±1.0°C. Altimeter accuracy ±1 meter. Humidity: +-3%
Reference: RBD-2056
Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5s
Reference: RBD-0564
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-2163
Built-in encoder Average output up to 420 pulses per revolution The brass faceplate has two mounting holes threaded Long D profile metal output shaft (0.354"/9.0 mm)
Reference: RBD-2858
Multi-Sensor Support: Works with various sensors like NTC thermistors, TCRT5000 line followers, and force sensors. Precise Control: Dual potentiometers for fine-tuning sensor thresholds. Wide Voltage Compatibility: LM393 chip ensures adaptability to diverse power sources. Compact & Durable Design: Integrates seamlessly into projects with a robust build.