Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0022
Affordable Price Operating Voltage: 5 V Sonar Sensing Range: 2-400 cm Max. Sensing Range: 450 cm Frequency: 40 kHz RoboticsBD
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-0132
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...
Reference: RBD-0145
Dual output mode, analog output more accurate A fixed bolt hole for easy installation With power indicator (red) and digital switching output indicator (green) Having LM393 comparator chip, stable. Operating Voltage: 3.3V~5V
Reference: RBD-0920
Acrylic Body. Easy to install. compatible with HC-SR04
Reference: RBD-0152
Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation
Reference: RBD-1069
Wheel Outer Diameter: 44MM Wheel width: 18 mm Tire material: Rubber Color: Black & White Weight: 18 gm Coder Accuracy: 12 pulses per revolution Wheel weight: 19.4 gm.
Reference: RBD-1070
Dimensions: 22 x 15 mm (Diameter x Height) Weight: 10 gm Body Case Material: Plastic Ball Material: 304 Stainless Steel Application: for MiniQ robot
Reference: RBD-0222
Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound
Reference: RBD-1071
Height: 11mm Width : 25mm Material: high-quality plastic
Reference: RBD-0150
Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~+40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser
Reference: RBD-1183
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-1775
Wago Compatible 2 Port, 3 Port, 5 Port, 221 Splicing Connector, Lever-Nut Assortment Pocket Pack for All Wire 12-24 AWG You will get the 1 pcs of the model of your choice. A- 2 Port. B- 3 Port. C- 5 Port. Please Choose Size Below
Reference: RBD-0352
Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-2473
Diameter: 34 mm D axis diameter: 3mm Tire width: 6.5 mm Suitable for mini Robots and Hobby kits.
Reference: RBD-2628
Connect and Build: Construct your robotic chassis with ease using this sturdy T connector. 2.5mm Acrylic: Offers durability and lightweight design for versatile robot creation. Right-Angle Connection: Creates a T-shaped junction for flexible chassis assembly. Universal Design: Compatible with 2WD, 4WD, and 6WD chassis configurations.
Reference: RBD-0331
Suitable for heavier goods and pressure resistance High elastic shock absorption for quiet operation Omni-directional wheel for flexible handling Thickened steel frame for increased bearing capacity Prevents floor damage from small objects
Reference: RBD-0128
Measure rotational speed with this 20-grid code disc for use with encoders and optocouplers. Compatible with various TT motors for DIY robotics projects and experiments. Lightweight and compact design for easy integration.
Reference: RBD-0427
Working voltage: 3.3V-5V Output form: digital output (0 and 1)
Reference: RBD-0663
Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD
Reference: RBD-0683
Operating voltage: DC3-5V Operating current: less than 20mA Sensor Type: Analog Detection Area: 40mmx16mm Operating temperature: 10℃-30℃ Humidity: 10% -90% non-condensing
Reference: RBD-0685
Detection distance: 2 ~ 30cm Detection angle: 35 ° Comparator chip: LM393 3mm screw holes for easy mounting
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-0823
LDR module 4 PIN Operating voltage 3.3V-5V Signal output indicator light. LDR module 4 PIN Able to detect ambient brightness and light intensity Adjustable sensitivity (via blue digital potentiometer adjustment)
Reference: RBD-1178
Size: 5mm Emitted Color : UV View Angle: About 20 - 25 degree. Luminous Intensity: 800mcd-2500mcd
Reference: RBD-1188
5 mm Clear Transparent Round Small Lens (Emitting Angle: 30 degrees) Forward Voltage / Direct Current : DC 1.5 Volt 20 mA (Low Voltage Energy Saving) Infrared Ray 850nm (Luminous Invisible Light) for Night Vision CCTV Security Camera Polarity (1.5 V) : Anode (Longer Part) | Cathode (Shorter Part)
Reference: RBD-1189
Wavelength: 850nm Emission Distance: 7 Meters / 23Ft Voltage: DC 1.2-1.3V Polarity: Anode (Longer Part) | Cathode (Shorter Part)