Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: RBD-1937
Brand: Goot Original
Equivalent 45W-60W Power Ergonomic Design Economically priced general purpose soldering iron. Compact and lightweight design for easy handling. Available with Long life tip.
Reference: RBD-2256
Brand: Goot Original
Equivalent 40W Ergonomic Design Economically priced general purpose soldering iron. Compact and lightweight design for easy handling. Available with Long life tip.
Reference: RBD-2488
Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet 10BaseT/100BaseTX Ethernet PHY embedded Auto-Negotiation (Full-duplex and half duplex) Support Auto MDI/MDIX Simultaneously Supports to 4 independent sockets 0.18 µm CMOS technology 3.3V operation with 5V I/O signal tolerance Provide Serial Peripheral Interface (SPI MODE...
Reference: RBD-0833
Soldering Iron KOOCU V501 25W Constant Temperature Electric Soldering Iron Soldering Stand Soldering Lead Solder Resin Wire Cutter Sucker
Reference: RBD-1390
Nema17 Bipolar. Number of Phases: 2. Step Angle: 1.8°. Phase Voltage: 2.6Vdc. Phase Current: 1.7A. Resistance: 1.5Ω ±10%. Inductance: 2.8mH ±20% (1KHz). Number of Wire: 4 (100cm Length). Holding Torque: 43N.cm. Shaft Diameter: Ø5mm. Motor Length: 40mm. Mass: 270g.
Reference: RBD-0119
Brand: Goot Original
DESOLDERING SUCKER GS-100 Manual pump for solder removal Light, strong, and economical plunger pump Color: Ivory Length: 330mm when stored Weight: 89g Diameter: ø23mm
Reference: RBD-1542
Model: A2212/10T Motor KV: 1400 Max. Efficiency Current: 6-12A No Load Current: 0.7A @10V Current Capacity: 16A/60S LiPO Batteries: 2S-3S
Reference: RBD-0493
Temperature Range : 0C-400C Shield Material : Metal Total Length(Approx.) : 2M / 6.6 Ft; Weight : 46g;
Reference: RBD-1414
Input Voltage (V): 100 ~ 270 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 4A. Load regulation (%): ±5. Input Plug: 2-Pin US type. Output Plug: DC Jack 5.5mm.
Reference: RBD-1596
Brand: Raspberry Pi Official
Good Quality material 96-230Vac operating input range 50,000 hours MTBF Input Current: 0.5A maximum Input Power consumption (no load): 0.075W maximum USB-C connection goes straight into your Raspberry Pi
Reference: RBD-1655
Input Voltage (V): 100 ~ 270 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 4A. Load regulation (%): ±5. Input Plug: 2-Pin US type. Output Plug: DC Jack 5.5mm.
Reference: RBD-1097
Frequency: 125Khz. Support μEM4001, 4100, or its compatible RFID, ID card. Read first 10 digits of the RFID/Proximity card. Support Windows95/98/2000/XP/7/8. Plug and Play Reliable working condition Powered directly from USB, no need external power supply
Reference: RBD-1723
Model: XKT-412. Input Voltage: 12V. Output Voltage: 5V. Operating Current: 1.2-2 A. Receive Coil: 3mm, the receiver output 5V / 1A current Normal Use Distance: 2 ~ 10mm Operating Current: 1.2-2 A.
Reference: RBD-2346
HW-671 WCS1800 Hall Current Sensor Over-current Protection Module Detection
Reference: RBD-0368
Thickness: 0.4mm Trigger Force: 20g, triggered (default resistance<200kΩ) Pressure Measuring Range: 20g~6kg Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz) Initial Resistance: >10MΩ Activation Time: <0.01S Operating Temperature: -40°C~+85°C Lifespan: >1million times Hysteresis: +10%,(RF+ -RF-)/FR+,1000g...
Reference: RBD-0670
Brand: RoboticsBD
Color: Grey Speed: 8500 RPM Collet Size: 0.5-3.0mm Full Accessories Set (14 pcs)
Reference: RBD-2397
GPS Module NEO-6M Satellite Positioning Module for Arduino with MicroUSB
Reference: RBD-0163
Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V Output voltage range (corresponding to 0-100%RH) DC 1-3.19V Test accuracy 5% RH
Reference: RBD-0169
Flex length: 5.6 cm. Total Length: 2.2″ (7 cm). Life Cycle : >1 million. Height : 0.43mm (0.017″), Flat Resistance: 10K Ohms ±30%. Power Rating: 0.5 Watts.
Reference: RBD-1543
Constant Current: 30A (Max 40A<10s). BEC: 5V 3A. Input Voltage: 11.1 ~ 11.7 V. Li-Po battery: 2S ~ 3S. Ni-MH 4-10 CELLS Auto Detect. Current stock is without connector
Reference: RBD-1909
6v 2800mah AA NI-MH Battery Rechargeable Battery Pack JST Plug
Reference: RBD-2174
Input Voltage : AC 100 – 240 V(50 HZ/60 HZ). Output Voltage: DC 24V. Output Current : 6A to 9A (no voltage drop). Output Power : 150W (maximum 220 W). Overload Protection: Yes. Over Current Protection : Yes. Short Circuit Protection: Yes.
Reference: RBD-1259
Model No: XW Power Eagle Lipo 1500mAh 7.4V 2S 25C Lipo Battery (T Plug Connector) Weight: 76 gm. Voltage: 7.4V. Dimensions : 26x34x72 (mm ). Max Continuous Discharge : 25C(25A). Balance Plug: JST-XH. Max Burst Discharge: 90 C (50A). Discharge Plug: T-Plug.
Reference: RBD-1258
Model No: XW Power Eagle Lipo 1000mAh 7.4V 2S 25C Lipo Battery (T Plug Connector) Weight: 76 gm. Voltage: 7.4V. Dimensions : 26x34x72 (mm ). Max Continuous Discharge : 25C(25A). Balance Plug: JST-XH. Max Burst Discharge: 90 C (50A). Discharge Plug: T-Plug.
Reference: RBD-0927
Weight: 85 gm. Voltage : 11.1 V. Dimensions : 17 x 34 x 72(mm ). Max Continuous Discharge : 25 C(25 A). Balance Plug : JST-XH. Discharge Plug : XT-60.
Reference: RBD-2462
HW-212 is a DC adjustable constant voltage constant current step down power supply module with LCD display.HD display input voltage and output voltage, current, power and display status.Adjustable stable output voltage and current.Set output current to meet the demand.It can be used as ordinary buck power supply module, charger and LED constant current...
Reference: RBD-2712
Tired of constantly replacing and disposing of 9V batteries for your electronics projects or robots? The Rechargeable DoublePow 9V Battery 280mAh with DP-D01 Charger is the perfect solution for you. This package includes both a high-capacity rechargeable battery and a versatile charger to meet your power needs efficiently and sustainably. Save Money...
Reference: RBD-2491
ATX Power Supply Breakout Board 3.3V, 5V, 12V and -12V Output Terminals ATX power supply breakout board allows for easy connection to the outputs of a standard ATX style PC power supply with 20 or 24 pin connections. Easily supply power to your projects from a high-quality and inexpensive (ofter surplus) PC-style power supply. This board provides +3.3V,...
Reference: RBD-2665
Introducing our versatile DC Buck Boost Power Module, a reliable solution for your power supply needs. This module offers both step-up and step-down functionality with overcurrent protection, ensuring safe and efficient operation. Key Features: Operating Voltage: DC 5V-30V Output Voltage: DC 0.6V-30V Output Current: 0-4A (with obstruction output...
Reference: RBD-2744
This power supply is an automatic step-up/down power supply module. When the output voltage remains constant, the input voltage is equal to the bottom, up or the output voltage. For example, to set output as 12V, the input voltage between 5 ~ 32V output voltage is always 12V. It can achieve continuous voltage, constant voltage, under-voltage protection,...
Reference: RBD-2742
AC input: AC 110-240V AC frequency: 50HZ/60HZ Output voltage: DC 24V Output Current: 4A-6A Output Power: 100W Modulation: Pulse width modulation