Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0335
Features: Simonk Programe, Perfect drive Low voltage, over heat protection, with power on self detection function MCU and BEC with independant regulator, high anti-interference ability Throttle stroke adjustable, compatiable with different receivers, good low speed performance
Reference: RBD-0042
Latest 6-axis flight control system with adjustable gyro sensitivity Permits super stable flight Lightweight airframe with nice durability
Reference: RBD-2299
Package Included: 1 * TS101 Controller 1 * Anti-slip cap 1 * Original TS tip 1 * Power Adpater (AC100-240V to 24V 3A) 1 * USB-C silicone cable 1 * Mini Soldering stand 1 * 15g Solder wire 1 * User Manual Miniware TS101 Hardware Specifications Power USB C PD and QC 3.0 9-20 Volts (9-45W) DC 9-24 Volts (9-65W) Soldering Iron Tip TS-B2 (Conical 10mm)...
Reference: RBD-0379
TS832 RC832 5.8G 32CH 250mW FPV Transmitter Receiver 7.4-16V
Reference: RBD-0380
Eachine VR D2 40CH 5 Inches 800 x 480 Raceband 5.8G Diversity FPV Goggles with DVR Lens Adjustable
Reference: RBD-0381
Operating Voltage:6~28 VDC Max Input Voltage:28 V DC Max Current Sensing: 90 A Connecting Type:XT-60 RoboticsBD
Reference: RBD-0437
Power supply range: 3.7-5V 100mA Resolution: 1280 x 960 Resolution: 600TVL Illumination: 0.5LUX Format: PAL / NTSC Audio Lens: Wide-angle 1.8mm (170º) Image sensor:1/4 CMOS image sensor Sensitive area: 3.5964mm x 2.7084mm Size of the lens: M10
Reference: RBD-0167
(Retired) Description: RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-20LA, a very simple to use RFID reader module from ID Innovations. With a built in antenna, the only holdup is the 2mm pin spacing....
Reference: RBD-0186
(Retired) WiDo - Arduino WIFI IoT(Internet Of Things) Node (Arduino Compatible) Wido is an Arduino compatible WIFI IoT Node development board, which integrates with WG1300 WIFI solution. The microcontroller of Wido is ATMEL ATmega32U4.
Reference: RBD-0211
(Retired) The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,
Reference: RBD-0741
Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards
Reference: RBD-0825
Improved Locking Gold Plated Connectors tip Color: Red High-Quality built and Material Good resistance to Temperature & High Amp. Current
Reference: RBD-0826
PolyMax 3.5mm Gold Connectors 3.5mm sprung gold connectors handle the large current, 50A+ systems. perfect for 3500mAh or larger capacity batteries
Reference: RBD-1157
Wick Width: 3 mm (+/- 2) Length: 1.5 Meter Material: Copper
Reference: RBD-0214
FPV Camera Color 480p This Camera Can be used with this Boscam FPV 5.8Ghz AV Transmitter and Receiver for FPV Purpose
Reference: RBD-0029
The first-generation Raspberry Pi Model B was released in February 2012 SOC BCM2835 Memory 256 MB Standard Form Factor Ethernet available. Wireless (Wifi/Bluetooth) not available. GPIO 26 pin
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-0013
Arduino Programming Supports fuses and lock bit programming Upgradeable for future device support Supports target voltages from 1.8V to 5.5V Adjustable ISP programming speed (50Hz to 8MHz SCK frequency) USB 2.0 compliant (full speed, 12Mbps) Powered from USB, does not require external power supply Target interface protection Short-circuit protection...
Reference: RBD-0025
With this Ethernet Shield, your Arduino board can be connected to internet Uses ENC28J60 SPI Ethernet controller and compatible HR911102A RJ45 socket Web client application to use Arduino as a distributed network sensor Stackable by accepting prototype shield or any other boards with Arduino compatible interface
Reference: RBD-0021
Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-1162
Net Content: 15g Paste Color: Brown Does not create High Smoke Does not create Foul/Bad Smell No Residual Waste High-Quality Soldering Additives & Activators for effective soldering Useful for general purpose soldering, electrical wires, components, and cables etc
Reference: RBD-0039
Model: HY-SRF05 Voltage : DC5V Static current : less than 2mA Detection distance: 2cm-450cm High precision: up to 0.3c
Reference: RBD-0043
Description: FEZ Hydra is a 100% open-source (hardware and software) .NET Gadgeteer compatible mainboard running .NET Micro Framework. It incorporates a 240Mhz AT91SAMRL ARM9 processor. With 16MB of SDRAM an 4MB of FLASH, FEZ Hydra is capable or running the most complex applications. The Basic Kit includes the essential modules needed to get started with...
Reference: RBD-0946
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Reference: RBD-0044
Brand: SparkFun Electronics
Description: The 72Mhz FEZ Panda II runs .NET Micro Framework, allowing users to program and debug FEZ Panda using Microsoft's free Visual C# Express. Applications are loaded over USB cable (or serial) with full featured debugging capabilities, such as stepping in code or inspecting variables.
Reference: RBD-0940
Good Quality Type: Male-Female Plated Connectors Length: 10 cm Color: Red and Black
Reference: RBD-2115
Toner transfer paper for DIY PCB Easily attach with Copper Board High quality Imported
Reference: RBD-0045
Description: Netduino 2 is still the same Arduino shield compatible board you know and love, except faster with more code space. Powered by an STmicro Cortex-M3 microcontroller running at 120MHz, the Netduino 2 packs 192KB of code space and 60KB of RAM. With built-in hardware peripherals like UART, PWM, I2C, 12-bit ADC and DAC, the Netduino 2 is ready to...
Reference: RBD-2283
Flexible-SC(FR) cable with 1x0.4 rm gauge size, Green color, and flame-retardant insulation material. Designed for electrical use in a variety of applications.
Reference: RBD-2282
Flexible-SC(FR) cable with 1x0.4 rm gauge size, red color, and flame-retardant insulation material. Designed for electrical use in a variety of applications.
Reference: RBD-0047
Brand: SparkFun Electronics
In the past, ARM processors were notoriously unfriendly in non-professional environments due to proprietary tool chains and unfamiliar instruction sets. Because of this, they were conspicuously absent from classrooms and hobbyists’ workbenches. LeafLabs aims to change this by providing an ARM tool-chain built from open source components and a programming...