How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-1098
Interface: I2C Operating Voltage: 3-5VDC Ports: 8-bit Parallel Ports Can be used with Arduino and Raspberry Pi
Reference: RBD-1417
SMD-MAX7219-MODULE A single module can drive an 8 * 8 common cathode lattice Module Operating voltage: 5V. Module with input and output interfaces Supports multiple modules cascade Led color: Red
Reference: RBD-2151
2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V
Reference: RBD-1399
Operating Voltage: 12V DC Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Equipped with high-current relay 10A@250VAC / 10A@30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick...
Reference: RBD-2220
Good PRINT PACK design, very beautiful. 8 world of the three primary colors (red-green-blue) LED color, scanning control mode. Applicable for various platforms, such as 51 / AVR / AVR / ARM / for Arduino All kinds of platforms.
Reference: RBD-2302
Low Standby Current. 1-to-8 Bidirectional Translating Switches. I2C Bus and SMBus Compatible. 5-V Tolerant Inputs. Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II. Note : Product may vary in two variants TCA9548A & PCA9548A
Reference: RBD-2316
1.Wide Analog Input Voltage Range: +/-5V2.Low “ON” Resistance: 80 ohm (type) at Vcc = 4.5V; 70 ohm (type) at Vcc = 6.0V; 60 ohm (type) at Vcc = 9.0V3.Logic Level Translation: to enable 5V to communicate with +/-5V analog signals4.Board Size: 30 x 19 mm
Reference: RBD-2470
3 Watt 8 Ohm Mini Speaker for Electronics Project with JST-PH2.0 Interface
Reference: RBD-2718
Dual-Channel Stereo Output Run-on 7V to 15V power Supply 32 Steps DC volume control has a +32dB to -75dB range. 40 pin QFN 6 x 6 mm package. Much higher efficiency in terms of cost and performance than competitors’ ICs
Reference: RBD-2734
Bi-directional mux can handle analog and digital signals.
Reference: RBD-2735
Measures high-side current and voltage up to 3.2A @ 26VDC.
