Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F

Reference: RBD-0578

Robotics Claw Mechanical Gripper Clamp Kit

4 reviews

The degree of Freedom (DOF): 2 Paw material: aluminum alloy. RoboticsBD Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm

Reference: RBD-1337

ESP8266 Dual WiFi Relay Module Internet Of Things Smart Home Mobile APP Remote Switch

1 review

Transmission Distance(m) :400 Relay Channel:2 Trigger Voltage (VDC): 5 Switching Voltage (VAC):250@10A Switching Voltage (VDC):30@10A Baud Rate:9600 Note: Relay might be different from the picture as per stock

Reference: RBD-2135

433 Mhz Remote Control and Wireless Receiver Module 4Ch output With Learning Button

433 Mhz Remote Control and Wireless Receiver Module Learning Code 1527 Decoding 4 Channel Output with Learning Button DIY kit for Arduino/ARM/MCU Suitable for wireless power switches, remote control sockets, LED lights, electric doors, and more.

Reference: RBD-1582

TDA7492P Bluetooth 4.2 CSR8635 Bluetooth Receiver Amplifier Audio Board 2x25W for 4/6/8/16 Ohm Speakers Module Parts Component

25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection

Reference: RBD-0686

NJK-5002C Hall Effect Proximity Sensor

2 reviews

Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines

Reference: RBD-2145

L298P Motor Driver Shield for Arduino

L298P based Arduino motor driver shield Onboard Buzzer (D4). Onboard Bluetooth interface, you can directly plug, no wiring required. Six Analog interface. Forward, Backward steering indicators

Reference: RBD-2111

DC Motor Speed Controller PWM 12V

DC Motor Speed Controller PWM 12V Controls the speed of a DC motor using Pulse-Width-Modulation (PWM) Provides continuous current of 3A to the motor or DC load Includes a 3A fuse for protection Supports reverse connection of power supply

Reference: RBD-1973

Brand: DFRobot

IO Extender for micro:bit

Easy-to-use  Low-cost expansion board for micro:bit Leads out all IO ports of micro:bit Specially-designed port for “HuskyLens AI camera”. This board can be used to Provide stable 5V power supply for HuskyLens to make it run steadily in all modes. Silkscreens on the back clearly indicate the functions of all interfaces

Reference: RBD-1388

Cap Conductive Slip Ring 4 Wire

1 review

A slip ring is an electromechanical device that allows the transmission of power and electrical signals from a stationary to a rotating structure. A slip ring can be used in any electromechanical system that requires rotation while transmitting power or signals. It can improve mechanical performance, simplify system operation and eliminate damage-prone...

Reference: RBD-1723

5V 2A Large Current Wireless Charger Module Wireless Power Supply Module

5 reviews

Model: XKT-412. Input Voltage: 12V. Output Voltage: 5V. Operating Current: 1.2-2 A. Receive Coil: 3mm, the receiver output 5V / 1A current Normal Use Distance: 2 ~ 10mm Operating Current: 1.2-2 A.

Reference: RBD-1330

AC Light Dimmer Module, 1 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

3 reviews

High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A

Reference: RBD-2573

Cap Conductive Slip Ring 6 Wire

A slip ring is an electromechanical device that allows the transmission of power and electrical signals from a stationary to a rotating structure. A slip ring can be used in any electromechanical system that requires rotation while transmitting power or signals. It can improve mechanical performance, simplify system operation and eliminate damage-prone...