Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0712
Signal input data processing auto measure waveform storage and transfer AC/DC voltage and current resistance diode continuity frequency duty ratio capacitance
Reference: RBD-1504
Input Voltage: 230V AC Output Voltage: 12V or 0V Output Current: 3 Amp Soft Iron Core. 3 Amp Current Drain.
Reference: RBD-1629
PR electronics, 5334A3B 2-Wire Programmable Transmitter 7.2-35 V DC
Reference: RBD-1630
MST 10RL-R01-03-100 Temperature Transmitter IN:PT100 OUT:4-20mA
Reference: RBD-0882
DIY Arduino Based Robotics Kit (Unassembled) 6Wheel Drive helpful for staircase Robotics & similar to all tertiary robotics Chassis made from High-Quality Cast Acrylic Bluetooth Based Wireless Android app-controlled Users can build 20+ different projects ex: staircase, obstacle avoiding, wireless controllable, etc.
Reference: RBD-1253
Program Software: Mixly + XR Scratch(base on Scratch2.0) Input: Edge sensor, Button, IR receiver module, Ultrasonic sensor, Tracking sensor Output: Buzzer, RGBLED, Two motor port,OLED CPU: Arduino UNO R3 Power: 2Pcs 3.7V DC Lithium battery Control: WiFi control/IR remote
Reference: RBD-1547
The custom-molded case for the Mavic Air 2, with better protection. Small, lightweight and maximum storage capacity Stylish yet indestructible IP34 Water resistant Removable shoulder strap and integrated carry handle for easy transport
Reference: RBD-2632
Plug-and-Play Simplicity: Get started in minutes with effortless setup and intuitive controls. Bluetooth App Control: Steer your robot and switch modes wirelessly from your smartphone/tablet. Obstacle Avoidance: Navigate obstacles with built-in ultrasonic sensor (avoidance mode). Line Following Mode: Robot autonomously follows pre-defined paths using line...
Reference: RBD-0880
Wooden robot chassis with 4 motors, 4 wheels, wire, switch, nut bolts, and clamps Multipurpose 4-wheel drive robotic car chassis kit Can be used to make a variety of robotic projects Easy to assemble with easy steps
Reference: RBD-0881
6WD wooden smart robot chassis with motor Includes wooden chassis parts, 6 double shaft BO geared motors, 6 plastic wheels, nut-bolts, 2 wires, and 2 switches Chassis size: 20x14.2cm Wheel diameter: 4.8cm BO motor voltage: 3-9v DC BO motor speed: 150RPM