Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0163
Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V Output voltage range (corresponding to 0-100%RH) DC 1-3.19V Test accuracy 5% RH
Reference: RBD-0426
Power supply voltage of 2.5 V ~ 5 V Low power consumption Wide detection range: 240 nm to 370 nm Wide Angle: 130 degrees Schottky type photosensitive diode Good linear response High sensitivity
Reference: RBD-0391
Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD
Reference: RBD-2212
Directly plug antenna interface. I2C bus communication. Multi-capacitor combined filter. Blue LED power indicator. High sensitivity(low noise RF input amplifier). High power auto gains control AGC circuit.
Reference: RBD-2147
The built-in 24bit AD converter. Immersion gold PCB, high quality, machine welding process to ensure quality. Power supply: 3 – 5V ( internal low dropout regulator ). Communication modes: Standard the IIC / SPI communication protocol.
Reference: RBD-0680
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules. RoboticsBD
Reference: RBD-2039
Product Name:DY-SV5W Voice Playback Module Product Number:DY-SV5W Work Voltage:DC 5V Working Temperature range:-20℃~85℃ Working Humidity range:0%-95%RH Size :35*35*4.5mm
Reference: RBD-1700
Brand: Waveshare
Mini ST-LINK/V2 Small single board Extreme low cost solution In-circuit debugger/programmer STM8 STM32.
Reference: RBD-1599
Brand: Raspberry Pi Official
RP2040 microcontroller chip designed by Raspberry Pi Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz 264KB of SRAM, and 2MB of onboard Flash memory 26 × multi-function GPIO pins 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels Temperature sensor
Reference: RBD-0569
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-2497
Compact size, measuring only 13*13*2.5mm Low power consumption High sensitivity and rapid response recovery Advanced MEMS technology Gas detected: CO Sensitivity: R0(in air) / Rs(in 150ppm CO) ≥ 3 Lifespan: ≥5 years (in air)
Reference: RBD-2527
Encoder Test Wire Length: 140mm. Wheel Dia.: 43 mm. Rated Voltage: DC 12V. Output Speed: 78RPM. Milling Edge: 0.5 mm. Output Shaft Size: 3 x 10mm. Output Shaft type: D type.
Reference: RBD-2528
Encoder Test Wire Length: 140mm. Wheel Dia.: 43 mm. Rated Voltage: DC 12V. Output Speed: 300RPM. Milling Edge: 0.5 mm. Output Shaft Size: 3 x 10mm. Output Shaft type: D type.
Reference: RBD-2529
Encoder Test Wire Length: 140mm. Wheel Dia.: 43 mm. Rated Voltage: DC 12V. Output Speed: 140RPM. Milling Edge: 0.5 mm. Output Shaft Size: 3 x 10mm. Output Shaft type: D type.