Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Are you interested in exploring more about Arduino programming? Robotics Bangladesh covers different ranges of shields with a vast number of different uses of Arduino projects. If you're interested in further exploring the world of shields, check out our Arduino shields on this website and use your Arduino for more than one purpose. Robotics Bangladesh has an awesome list of shields that you can choose to buy
Reference: RBD-1180
Standard For Shield interfaces and shape Can continue to stack other For expansion boards 3 M3 screw positioning holes for easy installation High Drive (5V or 3.3V) normally open contact closure Onboard relay indicator (red) Note: Relay might be different from the picture as per stock
Reference: RBD-1753
Digital I2S interface with high precision 24-bit data High signal to noise ratio is 61 dBA High sensitivity – 26 dBFS Stable frequency response from 60 Hz to 15 kHz Low power consumption: low current consumption 1.4 mA High PSR: -75 dBFS
Reference: RBD-2065
Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts
Reference: RBD-2293
801S is a vibration sensor with a gold alloy plated shock sensor and an onboard comparator IC. The sensor is capable of providing real-time vibrational data along with micro shock detection and about 60,000,000 times shock guaranteed. Pin Type Pin Description VDD Voltage Input pin GND Ground terminal D0 Digital Signal Output pin A0...
Reference: RBD-2307
This speaker is a great addition to any audio project where you need 8 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm...
Reference: RBD-2340
2 Channel PWM Pulse Frequency Adjustable Duty Cycle Square Wave Rectangular Wave Signal Generator Module to generate square wave for experiment development. This is used to drive stepping motor drivers' square waves, Generate an adjustable pulse for MCU using, and Generate an adjustable pulse for controlling the relative circuit (PWM adjust lightspeed, etc).
Reference: RBD-2426
1.5V USB ultrasonic mist maker driver board and atomizer plate. 2. Low driving voltage, low power, low impedance, stable waveform, high conversion efficiency. 3. Round ring atomizer plate, middle spray, 5um ultra-fine spray aperture, 740 ultra-dense spray holes. 4. The surface of the atomizing sheet adopts an oxidation-resistant silver layer to protect...
Reference: RBD-2415
Dual PS2 Game Joystick Button Module Joystick Compatible With Arduino is a module use to connect and interface PlayStation 2 (PS2) game joysticks with an Arduino microcontroller board. It provides a simple and convenient way to control various projects and applications using PS2-style joysticks. The module consists of two PS2 joysticks, each with two-axis...
Reference: RBD-2444
Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.
Reference: RBD-2449
Boosts a 3.5 – 35V input up to a 5 – 56V output @ up to 2A Require a Heatsink
Reference: RBD-2555
This is a self-contained switching module that energizes / de-energizes a relay based on the humidity level. Just add 5V power and hook up the load you want to control then adjust the potentiometer to set the relative humidity level at which you want the relay to switch between ON / OFF. This type of module can be used for applications such as to...
Reference: RBD-2728
Temperature controller module for both heating and cooling applications.