Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0922
Dimensions: 91 x 21 x 30 mm(LxWxH) Weight: 18 gm. Voltage: 3.3V or 5V. Port: Analog. Resistance: 10K. Appn: Raspberry-Pi projects. DIY projects., Arduino projects.
Reference: RBD-1019
Charging Voltage: 12.6V-13V Overcharge Voltage Range: 4.25V-4.35V ± 0.05V Overpressure Voltage Range: 2.3V-3.0V ± 0.05V Upper Limit Operating Current: 5A-6A
Reference: RBD-1066
Operating voltage: 5V DC. Detector distance: 1CM. Adjust the potentiometer, let the modules work normally. Small and easy to use module. It comes with a Buzzer for metal detection indication.The Mini Metal Detector Module arrives disassembled, requiring assembly using a soldering iron and soldering accessories. Moderate knowledge of soldering and...
Reference: RBD-1207
High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array...
Reference: RBD-1400
4-Channel Relay interface board and each one needs 15-20mA Driver Current. Both controlled by 12V and 5V input Voltage. Equipped with high-current relay, AC250V 10A ; DC30V 10A. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low). Indication LED’s for Relay output...
Reference: RBD-1530
Monomers Bearing: 30KG Permissible Load: 40KG M8 Thread
Reference: RBD-1559
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1560
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1575
Part Number: G3MB-202P Power supply:5VDC/160mA Trigger Voltage (VDC):5 Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-1753
Digital I2S interface with high precision 24-bit dataHigh signal to noise ratio is 61 dBAHigh sensitivity – 26 dBFSStable frequency response from 60 Hz to 15 kHzLow power consumption: low current consumption 1.4 mAHigh PSR: -75 dBFS
Reference: RBD-1949
N20 Micro Gear 12V 70RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel
Reference: RBD-2006
Feet Bracket 2mm Hard aluminum Sandblasting Surface Multifunctional Bracket Click here Long U Bracket Click here Short U Bracket Click here L-shaped Servo Bracket Click here Oblique U Servo Bracket Click here U Beam Servo Bracket Click here Humanoid Robot Feet Servo Bracket Click here One Word Frame Servo Bracket Click here Bearing for Servo Motor...
Reference: RBD-2065
Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts
Reference: RBD-2215
Working voltage (V): 3.3 ~ 5 Working current (A): Above 1A Operating Temperature (℃): -10 ~ +50 Mounting hole: M3 Detection range: 1mm ~ 60 cm adjustable.
Reference: RBD-2444
Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.
Reference: RBD-2458
The XH-M404 Adjustable DC-DC Step-Down Module can can step-down the input voltage to a range of 1.25 – 36V at up to 8A.
Reference: RBD-2460
LTC1871 DC-DC 3-35V To 3.5-35V Booster Step Up Module Converter Regulated Power 100W Buck-Boost Adjustable Supply LED VoltMeter