Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Selecting the most reliable sensor for any Application is quite tricky as you need to think over various specs like its size, accuracy, operating specifications, and most importantly, its price. Here, we carry around 150+ differential sensors with all technical specifications and its application guidelines to narrow down your search filters which gives the highest level of satisfaction to you. Explore a wide range of best-picked sensors by Robotics Bangladesh from top brands at sensible prices in Bangladesh.
Subcategories
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-0352
Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD
Reference: RBD-0685
Detection distance: 2 ~ 30cm Detection angle: 35 ° Comparator chip: LM393 3mm screw holes for easy mounting
Reference: RBD-1195
Temperature Coefficient Type: NTC Thermal Time Constant: 10s Resistance 10kΩ Tolerance: ±1%
Reference: RBD-1199
Low-noise output Fast power-on time Ratiometric rail-to-rail output 4.5 to 6.0 V operation Solid-state reliability Factory-programmed at end-of-line for optimumperformance Robust ESD performance
Reference: RBD-1209
Package type: leaded Package form: top view Radiant sensitive area (in mm2): 7.5 High photo sensitivity High radiant sensitivity Suitable for visible and near infrared radiation Fast response times Angle of half sensitivity: phi = ± 65°
Reference: RBD-2072
Operating Voltage: 3.3V-5V Features wide range voltage comparator LM393 Adjustable sensitivity Signal output indicator with the retaining bolt hole, convenient installation Output form digital switch output (0 and 1 high and low level) The output effective signal is low level When there is sound, outputs low level and the signal light
Reference: RBD-2085
Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH): 26 x 15 x 11 mm
Reference: RBD-2088
Operating Voltage: 5v DC. This module is Small and Simple to use. Digital switch output (0 & 1) High sensitivity Completes the circuit when the module is tilted LED lights up when tilt switch is activated
Reference: RBD-2089
Consists of a mercury switch 680Ω resistor LED that will light up when tilt is detected.
Reference: RBD-2784
A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Eventually, the battery runs down and goes below 3.3V, so the voltage to the ESP8266 core is too low, and could cause a lockup or corrupted data....