Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0737
Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-2830
Based on K210 RISC-V AI processor, the Maixduino AI development board comes with MI AI module and ESP32 module for WiFi and Bluetooth connectivity in the Arduino UNO form factor. K210 comes with a dual-core processor chip with independent FPU, 64 bits CPU bit width, 8 MB on-chip SRAM, 400 adjustable nominal frequency, and double-precision FPU supporting...
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: RBD-0353
Driver IC: SSD1306 Support wide voltage: 3.3V-5V DC Communication: IIC Working temperature: -30-80 degrees. RoboticsBD
Reference: RBD-1344
Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0491
Sensor Type: Inductive Sensing Distance: 0.197" (5mm) Output Type: NPN-NO, 3-Wire Response Frequency: 400Hz
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0492
Proximity-sensing / Diffuse Type Voltage: DC 6-36V Current: 300mA Sensory Distance: 5mm
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-1365
Central point temperature measurement high/low temperature auto tracking real-time temperature display Alarm buzzer: >37.2ºC: high temperature audible alarm
Reference: RBD-0270
AD/DA IO interface : screw terminal 1-WIRE interface : for connecting 1-WIRE devices like DS18B20 Sensor interface : for connecting various sensors 0.96inch OLED : SSD1306 driver, 128×64 resolution, SPI interface Buzzer CP2102 : USB TO UART converter PCF8591 : 8-bit AD/DA converter, I2C interface
Reference: RBD-1366
DT8380FC Infrared Thermometer Item no.: DT8380FC Temperature Range: -50~380°C/-58~716°F Measuring Accuracy: ±2% or 2C Distance Ratio: 12:1
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-1401
Measured variable Position Measuring principle Magneto-resistive Ambient temperature -40 °C ... 70 °C Repetition accuracy 0.2 mm Switching output PNP Switching element function N/O contact On time ≤1.3 ms Switch-off time ≤1.4 ms Max. switching frequency 150 Hz Max. output current 100 mA Max. output current in mounting kits 50 mA Max. switching capacity DC...
Reference: RBD-0396
Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD
Reference: RBD-1561
4-20mA -50 - 150C WEIGHT: 350.00g DIMENSIONS: 4.00cm x 4.00cm x 1.50cm
Reference: RBD-1568
Transmission distance: 1.2 mile (RS-485), 5 meters(RS-232) Transmission Speed: 300-115200 bps Working Modes: Asynchronous, half-duplex, differential transmission Transmission Media: Common wire, doule wire, UTP or Shielding Line Work Environment: -10°C to 85°C
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-1639
Operating Voltage: 12 V Self Locking Force: 500N Working temperature: -20ºC to +63ºC Aluminium frame and extension tube Compact Design Built in Limit Switch Low Noise Moisture-proof Surface Long life: A service life of more than 50000 times.
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-1653
Input Voltage: 88~264V/47~63Hz Output Voltage: 12V/4.2A DC Output Power: 50W
Reference: RBD-0413
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...
Reference: RBD-1675
Model: PZEM-004T Operating Voltage: 80-260VAC Test Voltage: 80-260VAC Rated Current: 100A Rated power: 100A / 22000W Operating frequency: 45-65Hz Measurement accuracy: 1.0
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0438
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD
Reference: RBD-1684
8 Channel DC 12V Pro mini Relay Shield Module PLC Timer Board for Arduino
Reference: RBD-0443
Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).