Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0989
Hold A standard 18650 batteries Wire : 15cm Output: 3.7v Dimension (Appro.): 76x20x20xmm Weight: 8gm High-quality plastic material
Reference: RBD-1309
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin EU type. Output Plug: Micro USB Plug. Compatible with: Raspberry Pi B+, 2, 2B, 2B+,3 ,3B+, Zero, Zero W. It has a switch so you can easily power off the device without having to unplug it right from the socket.
Reference: RBD-1414
Input Voltage (V): 100 ~ 270 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 4A. Load regulation (%): ±5. Input Plug: 2-Pin US type. Output Plug: DC Jack 5.5mm.
Reference: RBD-1524
Input Voltage(VDC): 4 ~ 40. Output Voltage(VDC): 1.3 ~ 37. Output Current: 2A Rated, ( 3A maximum with heat sink). Switching Frequency: 150 kHz. Input reverse polarity protection. Built-in output short protection function.
Reference: RBD-1535
Multiple Outputs: 5V+12V+12V Constant DC output, long backup time up to 6 hours Intelligent circuit design with over-charging, over-discharging and short circuit protections Suitable for 95% DC/USB digital products, such as: modem, router, CCTV camera, mobile phone etc.
Reference: RBD-1545
Input voltage 9~40V Output: 5V Maximum output current 2A Efficiency: 76-90% Material: electronic component
Reference: RBD-1559
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1560
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1562
Model: DP50V5A Input voltage range: 6.00-55.00V Output voltage range: 0.00-50.00V Output current: 0.000-5.000A Output power range: 00.00-250.0W
Reference: RBD-1564
High voltage resistant terminal. Support solar charging. Support undervoltage protection. Support short circuit protection.
Reference: RBD-0029
The first-generation Raspberry Pi Model B was released in February 2012 SOC BCM2835 Memory 256 MB Standard Form Factor Ethernet available. Wireless (Wifi/Bluetooth) not available. GPIO 26 pin
Reference: RBD-1596
Brand: Raspberry Pi Official
Good Quality material 96-230Vac operating input range 50,000 hours MTBF Input Current: 0.5A maximum Input Power consumption (no load): 0.075W maximum USB-C connection goes straight into your Raspberry Pi
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-1653
Input Voltage: 88~264V/47~63Hz Output Voltage: 12V/4.2A DC Output Power: 50W
Reference: RBD-0013
Arduino Programming Supports fuses and lock bit programming Upgradeable for future device support Supports target voltages from 1.8V to 5.5V Adjustable ISP programming speed (50Hz to 8MHz SCK frequency) USB 2.0 compliant (full speed, 12Mbps) Powered from USB, does not require external power supply Target interface protection Short-circuit protection...
Reference: RBD-1655
Input Voltage (V): 100 ~ 270 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 4A. Load regulation (%): ±5. Input Plug: 2-Pin US type. Output Plug: DC Jack 5.5mm.
Reference: RBD-0025
With this Ethernet Shield, your Arduino board can be connected to internet Uses ENC28J60 SPI Ethernet controller and compatible HR911102A RJ45 socket Web client application to use Arduino as a distributed network sensor Stackable by accepting prototype shield or any other boards with Arduino compatible interface
Reference: RBD-1673
Supports Qualcomm Quick Charge 3.0 fast charging protocol Has both "USB type C" and "Micro USB" port for charging power bank battery Power bank battery can be fast-charged (up to 15 watts) with QC 3.0 supported fast chargers Two "USB A" ports with maximum 18-watt power delivery from the power bank Power bank battery level indicator LEDs and power on/off...
Reference: RBD-0021
Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-1421
3S 11.1V 12.6V 20A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery). Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery). Continuous discharge current (upper limit): 20A (if the cooling environment is not good, please reduce the load current use). Continuous...
Reference: RBD-0039
Model: HY-SRF05 Voltage : DC5V Static current : less than 2mA Detection distance: 2cm-450cm High precision: up to 0.3c
Reference: RBD-1690
ON/OFF switch button on the power adapter. Very convenient for use. 5V 3A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-0043
Description: FEZ Hydra is a 100% open-source (hardware and software) .NET Gadgeteer compatible mainboard running .NET Micro Framework. It incorporates a 240Mhz AT91SAMRL ARM9 processor. With 16MB of SDRAM an 4MB of FLASH, FEZ Hydra is capable or running the most complex applications. The Basic Kit includes the essential modules needed to get started with...
Reference: RBD-1697
Brand: DFRobot
Takes a 6-12V input voltage. Outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. Powered from 6-12 DC2.1 power jack or from USB power. The maximum current it can provide is 500mA.
Reference: RBD-0044
Brand: SparkFun Electronics
Description: The 72Mhz FEZ Panda II runs .NET Micro Framework, allowing users to program and debug FEZ Panda using Microsoft's free Visual C# Express. Applications are loaded over USB cable (or serial) with full featured debugging capabilities, such as stepping in code or inspecting variables.
Reference: RBD-1702
Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-0045
Description: Netduino 2 is still the same Arduino shield compatible board you know and love, except faster with more code space. Powered by an STmicro Cortex-M3 microcontroller running at 120MHz, the Netduino 2 packs 192KB of code space and 60KB of RAM. With built-in hardware peripherals like UART, PWM, I2C, 12-bit ADC and DAC, the Netduino 2 is ready to...
Reference: RBD-1705
3A DC-DC Buck Step-down Converter Constant Voltage 5V Fixed Output Module
Reference: RBD-1723
Model: XKT-412. Input Voltage: 12V. Output Voltage: 5V. Operating Current: 1.2-2 A. Receive Coil: 3mm, the receiver output 5V / 1A current Normal Use Distance: 2 ~ 10mm Operating Current: 1.2-2 A.
Reference: RBD-0047
Brand: SparkFun Electronics
In the past, ARM processors were notoriously unfriendly in non-professional environments due to proprietary tool chains and unfamiliar instruction sets. Because of this, they were conspicuously absent from classrooms and hobbyists’ workbenches. LeafLabs aims to change this by providing an ARM tool-chain built from open source components and a programming...
Reference: RBD-1725
Power supply: DC 12V 1A Power range: 0~150.00W Capacity range: 0~999.999Ah Low voltage stop range: 0~150V
Reference: RBD-0048
Description: The BeagleBone is a low-cost credit-card-sized Linux computer from BeagleBoard that connects with the Internet and runs software such as Android 4.0 and Ubuntu. It's smaller and lighter than their other boards like the BeagleBoard-xM and while it may not have quite the processing power that their large model does, the BeagleBone is perfect...