Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0396
Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD
Reference: RBD-0936
High-Quality Pump Operating Voltage: 12VDC Flow Rate: 1100GPH Outlet Diameter 19mm
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0949
Operating Voltage : 2.5 ~ 4V Operating Current : 130 ~ 220mA Flow Rate : 80 ~ 120 L/H Maximum Lift : 40 ~ 110 mm Outlet Outside Diameter: 7.5 mm Outlet Inside Diameter: 5 mm
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-0950
Model : RS-360 micro-motors small pump Operating voltage : 4V-12V Current : 0.8A Motor diameter : 27 mm Pump Length : 52 mm Out of the water hole diameter : 4 mm Weight : 70g
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-0951
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-0413
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...
Reference: RBD-1056
Operating Voltage: 3 to 6VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 10mm (approx.) Weight; 15g (approx.)
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-1061
Low density: lightweight, low inertia. Capability to absorb shock and vibration as a result of elastic compliance. Ability to operate with minimum or no lubrication, due to inherent lubricity. The relatively low coefficient of friction. Operating Voltage(VDC): 3~12 Shaft Length (mm): 8.5 Shaft Diameter (mm): 5.5 (Double D-type) No Load Current: 40-180mA....
Reference: RBD-0029
The first-generation Raspberry Pi Model B was released in February 2012 SOC BCM2835 Memory 256 MB Standard Form Factor Ethernet available. Wireless (Wifi/Bluetooth) not available. GPIO 26 pin
Reference: RBD-0438
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-0443
Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
Reference: RBD-1114
N20 Micro Gear 12V 100RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel
Reference: RBD-0189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V
Reference: RBD-0013
Arduino Programming Supports fuses and lock bit programming Upgradeable for future device support Supports target voltages from 1.8V to 5.5V Adjustable ISP programming speed (50Hz to 8MHz SCK frequency) USB 2.0 compliant (full speed, 12Mbps) Powered from USB, does not require external power supply Target interface protection Short-circuit protection...
Reference: RBD-0550
Supply Voltage: 4.5 – 5.5 V. Current : <40 mA. Digital Interface : 5V TTL level for UART interface and GPIO. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. User-control General Pin Output. RoboticsBD
Reference: RBD-1249
Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 90mA
Reference: RBD-0025
With this Ethernet Shield, your Arduino board can be connected to internet Uses ENC28J60 SPI Ethernet controller and compatible HR911102A RJ45 socket Web client application to use Arduino as a distributed network sensor Stackable by accepting prototype shield or any other boards with Arduino compatible interface
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-0021
Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-0553
Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds
Reference: RBD-1257
Simple Plug and Play operation. USB input Plug It Can operate on any 5V DC power supply like Power bank 1 Meter cable with DC jack provides the convenience to connect and disconnect project easily
Reference: RBD-0039
Model: HY-SRF05 Voltage : DC5V Static current : less than 2mA Detection distance: 2cm-450cm High precision: up to 0.3c
Reference: RBD-0579
Quad-band 850/900/1800/1900MHz GPRS multi-slot class12 connectivity: max. 85.6kbps(down-load/up-load) GPRS mobile station class B Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands) Supports charging control for Li-Ion battery Supports Real-Time Clock Integrated GPS/CNSS and supports A-GPS Low power consumption, 10mA in sleep...
Reference: RBD-1340
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-0043
Description: FEZ Hydra is a 100% open-source (hardware and software) .NET Gadgeteer compatible mainboard running .NET Micro Framework. It incorporates a 240Mhz AT91SAMRL ARM9 processor. With 16MB of SDRAM an 4MB of FLASH, FEZ Hydra is capable or running the most complex applications. The Basic Kit includes the essential modules needed to get started with...
Reference: RBD-0684
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1