- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial IC
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Adapter
- PLC Programming Cable
- Tools, Hardware & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Miniature Vibrating Motor
A Miniature 3V Vibration Motor measuring only 21mm long and 7mm in diameter. Pre-wired with red & black leads 90mm. Ideal for alerts and feedback functions.
Store Pickup Available!
Free Ship Over 5000 BDT
Miniature vibration motor measuring only 12mm long x 6mm diameter. Coreless motor design, rated at 3V nominal.
These motors are often used for silent alert functions in mobile phones and are also used in applications within tools, robotics, control sticks and various alert functions in hand held equipment.
Pre-wired with red & black leads 90mm.
|Rated speed:||14000 RPM (2000 RPM)|
|Starting voltage:||1.7V max|
|Stall current:||140mA max|
Features: Model: YF-S201 Sensor Type: Hall effect Working Voltage: 5 to 18V DC (min tested working voltage 4.5V) Max current draw: 15mA @ 5V Output Type: 5V TTL Working Flow Rate: 1 to 30 Liters/Minute Working Temperature range: -25 to +80℃ Working Humidity Range: 35%-80% RH Accuracy: ±10%
The TFMini is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 30 centimeters and as far as 12 meters! As with all LiDAR sensors, your effective detection distance will vary depending on lighting conditions and the reflectivity of your target object, but what makes this sensor special is its size. Measuring...
IR Transmitter - White (5mm) 5 mm Clear Transparent Round Small Lens (Emitting Angle: 30 degrees) Forward Voltage / Direct Current : DC 1.5 Volt 20 mA (Low Voltage Energy Saving) Infrared Ray 850nm (Luminous Invisible Light) for Night Vision CCTV Security Camera Polarity (1.5 V) : Anode (Longer Part) | Cathode (Shorter Part)
Humidity Detection Sensor Module Rain Detection for Arduino
Specifications: Name:Radiation Detector system Model:508295 Geiger tube parameters: Technical parameters diameter:Φ10±0.5mm This is a kit version you have solder it yourself. Please check this file https://drive.google.com/folderview?id=0B9itH-BnWE5sY2JGRkM4MWhSYkE&usp=sharing To solder the board you can check "Sch__Geiger Counter Kit-v1.1.pdf" file
2.8V Regulator - Provides the required 2.8V for the sensor I2C Level Shifter - Provides logic level conversion from 2.8V to VCC 3-in-1 Module IR Emitter Range Sensor Ambient Light Sensor Measures absolute range up to 10cm Gesture Recognition I2C Interface Two Programmable GPIO Sharp Sensor Board Layout
Overview RDM6300 125KHz cardreader mini-module is designed for reading code from 125KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.
Specification: Module Name: MF522-ED Working current：13—26mA/ DC 3.3V Standby current：10-13mA/DC 3.3V sleeping current：<80uA peak current：<30mA Working frequency：13.56MHz Card reading distance ：0～60mm（mifare1 card） Protocol：SPI data communication speed：Maximum 10Mbit/s
ESP32 Development Board WiFi+Bluetooth Ultra Low Power Consumption Dual Cores ESP-32 ESP-32S Board
DESCRIPTION Sensor module for measuring current. Both AC and DC, up to 5A can be measured. The output is a linear voltage between 0 – VCC, centered around VCC/2 at 0A. The load is connected in series to the screw terminal. * Dimensions: 31 x 13mm* Supply voltage: 5V* Sensitivity: 185mV/A* Sensor: ACS712ELC-05B
Features: Precision Relative Humidity Sensor± 3% RH (max), 0–80% RHHigh Accuracy Temperature Sensor±0.4 °C (max), –10 to 85 °C0 to 100% RH operating rangeUp to –40 to +125 °C operating rangeWide operating voltage (1.9 to 3.6 V)
The DS18B20 digital thermometer provides 9-bit to 12-bit Celsius temperature measurements and has an alarm function with nonvolatile user-programmable upper and lower trigger points. The DS18B20 communicates over a 1-Wire bus that by definition requires only one data line (and ground) for communication with a central microprocessor. It has an operating...
MLX90614 Contactless Temperature Sensor Module For Arduino Compatible Application: Thermal Imaging Camera, Wireless Temparature Measure. Easy to integrateFactory calibrated in wide temperature range:-40…+125°C for sensor temperature and-70…+380°C for object temperature.
CCS811 Carbon Monoxide CO VOCs Air Quality Digital Gas Sensor Total Volatile Organic Compound (TVOC) sensing from 0 to 1,187 parts per billion eCO2 sensing from 400 to 8,192 parts per million Five Operating Modes Integrated MCU Onboard Processing Standard I2C Digital Interface Optimized Low-Power Modes Optional NTC Thermistor Pins
Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line
V3 Kit Voice Recognition Module BoardFor Arduino Compatible Sensor Voice Recognition Module is a compact and easy-control speaking recognition board.This product is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all. Max 7 voice commands could work at the same time. Sample Code & Library and Manual is available...
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...