Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2079
This is 38KHz Infrared IR transmitter sensor module For Arduino Transmit 38KHz modulating signal Suitable for Arduino DIY project Material: PCB
Reference: RBD-2442
8 channels can convert up to 8 logic signals Converts voltage levels between 1.2 to 3.6V and 1.65 to 5.5V systems Bi-directional with automatic direction control Each channel operates independently Optimized for open-drain applications like I2C, but can also work in push-pull applications Output enable allows outputs to be disabled
Reference: RBD-2003
Servo L Bracket 2mm Hard aluminum Sandblasting Surface Multifunctional Bracket Click here Long U Bracket Click here Short U Bracket Click here L-shaped Servo Bracket Click here Oblique U Servo Bracket Click here U Beam Servo Bracket Click here Humanoid Robot Feet Servo Bracket Click here One Word Frame Servo Bracket Click here Bearing for Servo Motor...
Reference: RBD-2546
The ADuM1201 is a dual channel digital isolator using technology by Analog Devices called iCoupler. It provides electrical isolation similar to an optocoupler and optionally provides logic level conversion between 3.3V and 5V systems.
Reference: RBD-2007
Head Bracket 2mm Hard aluminum Sandblasting Surface Multifunctional Bracket Click here Long U Bracket Click here Short U Bracket Click here L-shaped Servo Bracket Click here Oblique U Servo Bracket Click here U Beam Servo Bracket Click here Humanoid Robot Feet Servo Bracket Click here One Word Frame Servo Bracket Click here Bearing for Servo Motor...
Reference: RBD-2008
Inner Diameter (ID): 3 mm Outer Diameter (OD): 9 mm Width (mm): 4
Reference: RBD-2559
This Rich Shield has various sensors, buttons, LEDs, a potentiometer, segment display and buzzer. Specifications: Suitable for Uno, Mega, Leonardo and other 5V Arduino's that use the Uno R3 pin layout Works on 5V Has various parts to learn the basics with Arduino IR Remote Control is included Handy I2C and UART (RX/TX) pins available
Reference: RBD-2671
IC: 25Q64FVSIG-1935 Capacity: 64M-bit / 8M-byte Clock frequency: <104MHz Working voltage: 2.7V ~ 3.6V Current: 4mA Dimensions (LxWxH): 15.5 x 14.5 x 3.7 mm
Reference: RBD-2720
Chip type: W5500. Supports both 3.3V & 5V. Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE. 10BaseT/100BaseTX Ethernet PHY embedded. Supports automatic response (full duplex/half duplex mode). Internal 32Kbytes Memory for Tx/Rx Buffers.
Reference: RBD-2725
Onboard LM386 Chip. 200 multiplier benefits circuit design. On-board speaker wiring Block. On-board 10K variable resistor, you can adjust the volume of the enlarged. Onboard power indicator.
Reference: RBD-2727
Module can be used to expand the digital I/O of an MCU using the I2C bus.
Reference: RBD-2734
Bi-directional mux can handle analog and digital signals.
Reference: RBD-2736
2×8 connector, easy with the MCU mount. Jumper selectable can work in parallel or serial mode. On board 3.3 V LDO 1117, provides 800 mA current. 5 V power supply is powered by the target board. 12 MHZ crystal.
Reference: RBD-1699
Brand: SparkFun Electronics
Simple switches Detect a collision SPST switch
Reference: RBD-2737
Chipset : AT24C256. Operating Temperature: -55°C to 125°C. Storage Temperature: -65°C to 150°C. The voltage on Any Pin with respect to the ground: -1.0V to 6.25V. Maximum Operating Voltage: 6.25V DC.
Reference: RBD-2740
Precision 12-bit Digital-to-Analog converter with I2C interface
Reference: RBD-2741
Module mounts an 8MB serial flash chip for easy use with breadboards.
Reference: RBD-2394
Smart Robot Rubber Wheel Support Stepper Motor and DC Motor Size:47*33.8*12mm Diameter: 48 mm D Shaft Size: 3 x 5mm Tire width: 12 mm Material: Rubber and ABS Plastic Suitable for mini Robots and Hobby kits. 1 pcs only
Reference: RBD-2761
ICL8038 12V to 15V, Signal Generator, Medium/Low Signal, Frequency 10Hz-450KHz, Triangular/Rectangular/Sine Wave Generator, Module Working voltage: 12V ~ 15V Output: Triangular wave, Square wave and sine wave. Frequency range: 10HZ ~ 450kHz Low distortion sine wave: 1% Duty cycle range: 2% to 98% Low temperature drift: 50ppm / ℃ Triangular wave output...
Reference: RBD-2858
Multi-Sensor Support: Works with various sensors like NTC thermistors, TCRT5000 line followers, and force sensors. Precise Control: Dual potentiometers for fine-tuning sensor thresholds. Wide Voltage Compatibility: LM393 chip ensures adaptability to diverse power sources. Compact & Durable Design: Integrates seamlessly into projects with a robust build.
Reference: RBD-2782
Note: Without Motor Features: Motor mounting bracket Name: TT motor aluminum alloy bracket Length: 22 mm Width: 12 mm The thickness of 5 mm Material: aluminum alloy Kit include: 1*TT motor aluminum alloy bracketComplete set of screws: