Reference: RBD-2247

Digital Display for HC-SR04 Ultrasonic Distance Measurement Control Board

Onboard STM8S103 high-performance microprocessor With digital tube display Valid Measurement Distance: 3-400cm Display Unit: cm Maximum Input Voltage: 5VDC 2.54mm White Socket: 5V power interface.

Reference: RBD-2462

Buck Converter CC CV 1.2V-32V 5A Adjustable Regulated Power Supply Voltmeter Ammeter DIY Kit

HW-212 is a DC adjustable constant voltage constant current step down power supply module with LCD display.HD display input voltage and output voltage, current, power and display status.Adjustable stable output voltage and current.Set output current to meet the demand.It can be used as ordinary buck power supply module, charger and LED constant current...

Reference: RBD-1842

Stainless Steel 1m Conductive Thread Wire for Wearable Lilypad

Material: 12UM Stainless steel fiber Gram Weight: 0.2458g/m Strength: 2.8KGF. Length: 1m. Diameter(mm): 0.12. Resistance (Ω/m) : 27.

Reference: RBD-1367

RGB Full color LED SMD Module

RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing Working voltage: 5V LED drive mode: Common cathode driver

Reference: RBD-2212

TEA5767 Stereo FM Radio Module with Detachable Antenna

Directly plug antenna interface. I2C bus communication. Multi-capacitor combined filter. Blue LED power indicator. High sensitivity(low noise RF input amplifier). High power auto gains control AGC circuit.

Reference: RBD-2095

Infrared Obstacle Avoidance Sensor Module

Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 ° **Please be advised that the majority of our customers have left negative reviews for this product. We recommend that you do not make a purchase unless you are absolutely certain that you can...

Reference: RBD-1266

Prototype Shield With Breadboard for Arduino

It has a nice standard 0.1″x0.1″ prototyping grid with big pads Comes with Stacking headers and plain header, choose whichever you want when soldering together An IC pattern for adding DIP ICs up to 20 pins Power rails down the middle and sides A reset button and an extra general use button Two 3mm general use LEDs, red and green, as well as 2 matching...

Reference: RBD-1912

L293D Motor Driver Module

New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)

Reference: RBD-2306

WS2812B RGB LED 12 Bit Ring

The 12 Bit RGB LED Ring Module with Integrated Drivers – WS2812B can be used in colourful curtain-up/ flow water/raindrop/jump flash and so on hundreds of lighting effects. There is a single data line with a very timing-specific protocol. It has trichromatic colour for each pixel and can complete 16,777,216 colours of all true colour displays, the...

Reference: RBD-2241

LilyPad SMD LED White Color

Wearable e-textile technology.  Designed with large sew tabs LED White Color

Reference: RBD-2044

ESP32-CAM-MB MICRO USB Download Module for ESP32 CAM Development Board

Model: ESP32-CAM-MB Color: Black Chipset: CH340G Connectivity Technology: USB Note: The camera module is not included with the board.

Reference: RBD-2397

GPS Module NEO-6M Satellite Positioning Module for Arduino with MicroUSB

GPS Module NEO-6M Satellite Positioning Module for Arduino with MicroUSB

Reference: RBD-1769

Mini MP1584EN DC-DC BUCK Adjustable Step Down Module

Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current:  1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor

Reference: RBD-2316

CJMCU-4051 74HC4051 8 Channel Analog Multiplexer/Demultiplexer Breakout Board for Arduino

1.Wide Analog Input Voltage Range: +/-5V2.Low “ON” Resistance: 80 ohm (type) at Vcc = 4.5V; 70 ohm (type) at Vcc = 6.0V; 60 ohm (type) at Vcc = 9.0V3.Logic Level Translation: to enable 5V to communicate with +/-5V analog signals4.Board Size: 30 x 19 mm

Reference: RBD-0564

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-2362

CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi

Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit...

Reference: RBD-0699

1.8" inch TFT LCD Display module ST7735S 128x160

Display Size: 1.8″ Driver IC: ST7735 Input Voltage (V): 3.3 to 5 Pixel Resolution: 128 x 160 Interface Type: SPI

Reference: RBD-2156

4×4 Matrix 16 Keyboard Keypad

Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key.

Reference: RBD-2718

PAM 8610 Digital Stereo Class-D Amplifier Board 2x15W Output

Dual-Channel Stereo Output Run-on 7V to 15V power Supply 32 Steps DC volume control has a +32dB to -75dB range. 40 pin QFN 6 x 6 mm package. Much higher efficiency in terms of cost and performance than competitors’ ICs

Reference: RBD-1038

PIC Development Board with Cable PIC16F877

Reset button.  4M crystal onboard, Using socket, Crystal frequency can be replaced easily at any time  4 independent push buttons, connected to RB0 RB1 RB2 RB3  8 LED's connected to the RD port, J3 is jumpered to enable LED. Remove to disconnect.  Standard RS232 communication interface, microcontroller computer communication interface. 

Reference: RBD-2734

74HC4067 16-Ch Analog / Digital Mux Module

Bi-directional mux  can handle analog and digital signals.

Reference: RBD-0419

SparkFun Particle Sensor Breakout - MAX30105

Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...

Reference: RBD-2541

Brand: DFRobot

Gravity: Voice Recorder Module

This is the latest voice recorder module with integrated record and play functions. Easily record your voice by pressing the record button, speaking and then releasing the button when finished. The module is able to playback 10 seconds in total. Connect an 8Ω 3W speaker or an external active speaker for voice output. The module also has a 3 pin digital...

Reference: RBD-1929

3.5inch HDMI Display-B

General-purpose HDMI display, Connecting computers, TV boxes, Microsoft Xbox360, SONY PS4, Nintendo Switch and so on Can be used as Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, Win10 IOT, single-touch, free drive Can be used as PC monitor, support Win7, Win8, Win10 system (No touch Function)

Reference: RBD-2564

LR7843 MOSFET Switch Control Module

This MOSFET module with optoisolation uses the LR7843 N-Channel logic compatible MOSFET with ultra low Rds(on) for moderate to higher current low-side switching applications of up to 15A continuous. N-Channel logic compatible MOSFET with optoisolation and ultra low 3.3mΩ Rds(on)

Reference: RBD-2725

LM386 Audio Amplifier Module

Onboard LM386 Chip. 200 multiplier benefits circuit design. On-board speaker wiring Block. On-board 10K variable resistor, you can adjust the volume of the enlarged. Onboard power indicator.

Reference: RBD-2089

Mercury Medallion Module

Consists of a mercury switch 680Ω resistor LED that will light up when tilt is detected. 

Reference: RBD-2658

1 Channel 12V 30A Relay Control Board Module with Optocoupler

This 1 channel 12V 30A relay control board module with optocoupler modules is compliant with international safety standards, control and load areas isolation trenches it has a single relay a genuine. The inputs of 1 Channel 12V 30A Relay Module are isolated to protect any delicate control circuitry. It can be used as a single chip module for appliance...

Reference: RBD-2094

DHT11 Digital Relative Humidity and Temperature Sensor Module

The module can detect the surrounding environment of the humidity and temperature High reliability and excellent long-term stability The output from the digital output Humidity measuring range: 20%~90%RH(0~50 degree (temperature compensation). Temperature measuring range: 0~+50degree. Humidity measurement accuracy: ±5.0%RH. Temperature measurement...

Reference: RBD-0737

5V 1 Channel Solid State Relay (SSR)

Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac