Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0311
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD
Reference: RBD-0664
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity X: 28.6 LSB/g. Sensitivity Y: 31.2 LSB/g. Sensitivity Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection. RoboticsBD
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-2175
4-port charger for single-cell 3.7V LiPo batteries Uses MCP73831T Charge Management Controller IC for reliable charging Standard Mini USB socket for 5V USB power source Selectable charging rates of 500mA or 100mA (default set to 500mA) Status LED indicates charging status Suitable for 3.7V LiPo or Li-ion batteries with Micro JST Connector USB charger...
Reference: RBD-1757
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity: X: 28.6 LSB/g. Y: 31.2 LSB/g. Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection.
Reference: RBD-1159
Removes all Solder Residue Low cost and high-quality Ideal replacement for the old sponges. Removes excess solders from soldering iron tips Provides extended tip life
Reference: RBD-1165
9 Layer Acrylic stylish case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel
Reference: RBD-2643
Pixel chain - 25x LED 5mm Cool White 25 bright LEDs in cool white color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2247
Onboard STM8S103 high-performance microprocessor With digital tube display Valid Measurement Distance: 3-400cm Display Unit: cm Maximum Input Voltage: 5VDC 2.54mm White Socket: 5V power interface.
Reference: RBD-2706
Pixel chain - 25x LED 5mm Purple 25 bright LEDs in purple color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2623
This robust 9V 3A AC-DC adapter delivers reliable power to high-current electronics like prototypes, development boards, routers, and more. 3A output caters to demanding devices, eliminating power limitations. Works globally with 110-240V AC input voltage. Small size and lightweight design ensure portability and convenient storage. Features over-voltage,...
Reference: RBD-2377
Universal battery charger for AA, AAA, and 9V Ni-MH or Ni-CD batteries Can charge 2-4 AA or AAA batteries at once, or 1 or 2 9V batteries Charging current of 200mA for AA batteries and 150mA for AAA batteries LED indicators show the charging status Compact and portable design
Reference: RBD-2200
Different accessories have different functions to meet multiple needs. Suitable for surface cleaning, derusting, grinding, dusting, deburring, polishing, stripping residue, etc. Good polishing effect, high efficiency, low cost. Fit for your polishing need, can use for metal and nonmetal materials. Wear-resistant and durable, not easy to wear, long service...