Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0269
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-1746
Neodymium Magnet Shape: Disc Dimension: 10mm x 1mm
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-2695
Custom 3D-printed enclosure designed specifically for the US-015 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. Features two screw holes for convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-2696
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-2027
5.08mm pitch. Pin header: Tin plated brass. Contacts: Nickel plated brass. Strong, compact, lightweight. Heat resistant.
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-2021
Current Rating: 3A Voltage Rating: 250V Connector Type: Header JST-XH 4 Pin Connector
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-0702
It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock
Reference: RBD-1659
Dimension: 5×7 CM Quantity : 1 PCS Base Material FR4 Copper Thickness 1-4 OZ Board Thickness 1.6 PCB Weight; 10 gm PCB color: Green
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-1115
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1116
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1117
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1118
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1119
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1120
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1121
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connection
Reference: RBD-1122
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1123
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.