Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0313
Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0269
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-2142
Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.
Reference: RBD-2162
USB Type: Type-A to Mini-B Length: 1 meter/ 3.2 Feet Exclusively designed for Arduino boards. Compatible with Arduino Nano Larger Cable
Reference: RBD-1761
USB Type: Type-A to Type-B Weight: 80 gm. Length: 1m / 3.2Feet Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
Reference: RBD-2182
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below.
Reference: RBD-2195
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-2196
USB Type: Type-A to Type-B Weight: 26 gm. Length: 50 cm Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
Reference: RBD-2695
Custom 3D-printed enclosure designed specifically for the US-015 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. Features two screw holes for convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-2696
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-2311
USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.
Reference: RBD-2362
Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit...
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-2425
Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.
Reference: RBD-0702
It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-1065
Latest Arduino CNC Shield Version 3.10 GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) Coolant enable Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) Compact design. 4-Axis support (X, Y, Z, A-Can duplicate...
Reference: RBD-1098
Interface: I2C Operating Voltage: 3-5VDC Ports: 8-bit Parallel Ports Can be used with Arduino and Raspberry Pi
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.