Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-0032
USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: RBD-2199
Compatible with the Arduino IDE, making it easy for beginners to start using Smaller and cheaper than traditional Arduino boards Powered by a 16.0 MHz microcontroller Fully assembled except for headers, allowing for easy soldering Great for projects where size and cost are a concern Perfect for beginners to jump into electronics Can be used for a variety...
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0987
Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.
Reference: RBD-0662
Power supply: 7V to 30V. The higher the voltage, the higher the torque at high speeds. Adjustable current control from 150mA/phase to 750mA/phase. Logic voltage: 5V or 3.3V. A3967 microstepping driver. RoboticsBD
Reference: RBD-0684
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
Reference: RBD-1523
Microcontroller: ATmega328P Circuit Operating Voltage: 5V Clock frequency: 16MHz. 6 PWM port: D3, D5, D6, D9, D10, D11. Use For Atmel Atmega328P-AU microcontroller. Support serial download. Support 9V battery. A pair of TTL level serial port transceiver : RX / TX.
Reference: RBD-1724
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-2389
This module is ideally suited to motor control to your project. This is the L298N Dual H-Bridge module which allows you to build in 2 controlled motors to your projects, controlling the speed with current. This can be used with a wide range of microcontrollers including Arduino and Raspberry Pi.
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-1242
6-piece Acrylic case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble without any Screws or Nut-Bolts Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel Mounting holes and anti-slip rubber feet at the back.
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-0110
রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক। আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা 5V,3A. আমরা আমাদের টেস্ট এ 5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন। এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...
Reference: RBD-1702
Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-1933
Length: 1M Diameter: 3 mm. Color: Black Material: PE/PVC/ABS
Reference: RBD-1156
Brand: Raspberry Pi Official
FPC (Flexible Printed Circuit) cable. Length: 16cm. Ways: 15-way. Pitch: From 0.5mm(Raspberry Pi Zero) to 1.0mm (Raspberry Pi Camera and Raspberry Pi 3). Compatible with 5MP Raspberry Pi Zero W Camera.
Reference: RBD-1875
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-1145
Version 1.4 HDMI to micro HDMI cable Supports 480i ,480p, 720p, 1080i, 1080p, 1440p resolution Cable Length: 1.5m Color: Black Application: Mulitimedia
Reference: RBD-2160
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: RBD-0945
Length: 1.5m Weight: 82 gm. Color: Steel Black Supports all HDTV devices including 1.4 Supports resolution up to 1080P Supports 3D and Blu-ray Disc
Reference: RBD-1368
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-2309
Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! This module contains an ESP8285, which is an ESP8266 processor with 1MB of FLASH memory already built in. You can use it just like an ESP8266, it's the same processor and WiFi The ESP8266 processor from Espressif is an 80 MHz microcontroller with a...
Reference: RBD-0109
Support HD resolution, super clear picture, fast transmission speed The maximum signal range up to 1920 X 1200, 1080p; Video input signal: 5Volts p-p(TTL) ; Support VGA video bandwidth: 10 bit, 162MHz Video amplifier bandwidth: 162MHz Support resolution up to 1920 X 1200, reduce blank signal during transmit. No external power supply, plug, and play.
Reference: RBD-1059
This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use. You just need to click them together after you fix your pi board on it with screws.
Reference: RBD-2413
Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-0943
Method: connect with computer keyboard wireless,wireless mouse Keyboard interface: 2.4 G wireless The mouse interface: 2.4 G wireless Work style: photoelectric Optical resolution: 1600-1200-800 DPI Whether to supportplug and play: support If there is a multimedia function keys: yes Whether to support the human body engineering:support Applicable...