Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1153
135 quality jumper Color: red, orange, yellow, green, blue, purple, gray, brown, white. Box size: 165 × 55 × 10 (LxWxH) mm. 140 pcs of 22 AWG solid wires
Reference: RBD-0343
Model number: TEC1-12706 Operating Voltage: 12V Maximum Voltage Umax (V) : 15.4V Maximum Current Imax (A) : 6A Maximum Power: 92 W Maximum Temperature: 138°C Power Cord: 200mm.RoboticsBD
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-1952
Digital Multi Meter Banana Plug To Test Hook Clip Probe Cable Length: 1 Meter Voltage: 1000V 20A Weight: 43g
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-1589
Solder cup configuration for longevity. Nickel-plated terminals. Gold plates pins. Good quality.
Reference: RBD-0395
Input voltage range: 4V-38V DC Output voltage range: 1.25V-36V DC adjustable. Output current: 0-5A. Output power: 75W. High efficiency up to 96% The built-in thermal shutdown function Built-in current limit function In-Built output short protection function. RoboticsBD
Reference: RBD-1676
L Shape 3.5Mm Right Angle Female To Male Plug Adapter Connector
Reference: RBD-2425
Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.
Reference: RBD-2427
Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.
Reference: RBD-0410
Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-1770
Brand new and high quality Included USB transceiver, without external circuit device With 3.3V and 5V dual power output With three LEDs: power indicator, data reception indicator, the data transmission indicator, working status Meets the USB2.0 specification requirements With self-recovery fuse. In the event of the accidental short circuit, it can...
Reference: RBD-0668
Crystal 32.768KHz, matching capacitance 6pF DS1302 8-pin SMD homemade chips Seconds, Minutes, Hours, Day of Month, Day of Week, and Year Operating temperature: 0 degree — 70 degree. RoboticsBD
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-2705
Micro USB data cable with an 8mm extended connector for phones and tablets with deep ports. Supports both charging and data transfer for versatile use. Tangle-free cable material ensures easy use and prevents knots. 1-meter length provides convenient reach for charging and data syncing.
Reference: RBD-0729
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-0737
Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-2927
Stepper Motor Cable XH2.54 4Pin to PH2.0 6Pin – 1.5 Meter
Reference: RBD-2180
Testing hook clip multimeters test lead extension probe Safety handle and spring hook type alligator clip Converting connection for probes with whorl pattern Made of high quality material, durable to use and provide great performance Compact design, easy to carry
Reference: RBD-0963
Current and voltage display in turn, easy and comfortable to use. Small and portable, do not need other power supply. Measuring range: DC 3V – 9V / 0 – 3A (up to 5A ) Portable Device Interface: USB2.0, USB3.0 Product Weight: 0.025 kg Two output ports
Reference: RBD-1326
Outer Diameter: 68 mm. Supply Voltage: DC 4-7V. LED driver chip: WS2812B Communication interface: single wire communication. Send data at speeds of 800Kbps. The color of the light was highly consistent Full-color module, Full-color soft lights a lamp strip
Reference: RBD-2408
Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also if say you want to JTAG program a board that you can't solder headers to.Total Length: 17.5mmTop Length Length: 15mmPin Spacing 2.54mmStrip...
Reference: RBD-2463
The SOP8 test clip is made of high-quality plastic and copper metal, which is durable and can be reused.When using the SOP8 test clamp, do not force it down, open the clamp and clamp it in from the left and right sides of the chip.The same is true when disassembling, you can't pull it out directly, you must first separate the clip from left to right, and...
Reference: RBD-2472
Note: Please be aware that once the connector is closed it can't be unlocked
Reference: RBD-2530
DE-9 (DB-9) Female Socket Connector to Terminal Block Breakout
Reference: RBD-1524
Input Voltage(VDC): 4 ~ 40. Output Voltage(VDC): 1.3 ~ 37. Output Current: 2A Rated, ( 3A maximum with heat sink). Switching Frequency: 150 kHz. Input reverse polarity protection. Built-in output short protection function.
Reference: RBD-2531
DE-9 (DB-9) Male Socket Connector to Terminal Block Breakout
Reference: RBD-2575
A gender changer is a hardware device placed between two cable connectors of the same type and gender. An example is a cable connector shell with either two female or two male connectors on it (male-to-male or female-to-female), used to correct the mismatches that result when interconnecting two devices or cables with the same gender of connector.