Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0269
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-1161
Premium Quality Soldering Wire/Lead Low Melting Point Weight: 20-22 Gram 0.8mm Known as Lead or Solder Wire Melting Temperature 180°C Approx. (Tested by RoboticsBD LAB) We suggest this solder wire/lead paired with this solder to make your soldering work easier. Check GOOT Original KX-60R Soldering Iron 45W Check GOOT Original Soldering Iron TQ-77 here
Reference: RBD-1162
Net Content: 15g Paste Color: Brown Does not create High Smoke Does not create Foul/Bad Smell No Residual Waste High-Quality Soldering Additives & Activators for effective soldering Useful for general purpose soldering, electrical wires, components, and cables etc
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-1166
Heavy-duty base to uphold the weight of Soldering iron Nickel-plated spring holder Spring holder provides substantial room for holding the soldering iron support
Reference: 1169
Please select your desired models from the list below.
Reference: RBD-2695
Custom 3D-printed enclosure designed specifically for the US-015 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. Features two screw holes for convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-1107
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 12 Low Current Consumption High Brightness Easy to Use with PCB Mounting as well as on Breadboard
Reference: RBD-2696
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-1109
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 20 Low Current Consumption High Brightness
Reference: RBD-1171
New Solder Sucker Desoldering Pump Tool Removal Vacuum Soldering Iron Desolver Metal Body, high sucting power, light weight. RoboticsBD Back pull pattern for the inner spring instantaneous suction is strong. Slimline outlook, airtight structure allow one-headed operation. All metal construction is ideal for heavy use including production re-work and...
Reference: RBD-1184
5.08mm pitch. Pin header: Tin plated brass. Contacts: Nickel plated brass. Strong, compact, lightweight. Heat resistant.
Reference: RBD-1185
Rated Voltage: 300V Rated Current: 20A Withstanding Voltage: AC2000V/1Min Wire Range: 22-12 AWG
Reference: RBD-1186
5.08mm pitch. Pin header: Tin plated brass. Contacts: Nickel plated brass. Strong, compact, lightweight. Heat resistant.
Reference: RBD-1108
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 12 Low Current Consumption High Brightness
Reference: RBD-1305
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common anode No. of Pins: 10 Low Current Consumption High Brightness
Reference: RBD-1306
Easy to Install on Breadboard. Bright LED lights. Compact Design. LED Size: 3mm. Configuration: Common Anode.
Reference: RBD-1268
Mediocre Quality Lead Name: Tong Kong Wire Diameter: 0.8mm 60/40 Tin/Lead Solder Wire Flux: 2% SWG: 20/22 Net Weight: 32g Melting Temperature 280°C Approx. (Tested by RoboticsBD LAB)
Reference: RBD-1406
High-Quality cable One male and one female connector. Flat 30cm Servo Lead Extention (JR) Quality wire and connectors used. Great for larger planes with servos that experience high loads.
Reference: RBD-1430
Double Pole Double Throw. Main Body: 12 x 12 x 10mm. Lever Length: 11mm.
Reference: RBD-1587
It is a perfect solution for those who want to make custom power cable. This CCTV Camera DC Power Connector will provide a great connection. The internal diameter of the plug: 2.1mm The external diameter of the plug: 5.5mm