Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0670
Brand: RoboticsBD
Color: Grey Speed: 8500 RPM Collet Size: 0.5-3.0mm Full Accessories Set (14 pcs)
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-0833
Soldering Iron KOOCU V501 25W Constant Temperature Electric Soldering Iron Soldering Stand Soldering Lead Solder Resin Wire Cutter Sucker
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-2489
Wiznet Compact W5500 Network Module - 10/100 Base T WIZ850io is a compact size network module that includes a W5500 (TCP/IP hardwired chip and PHY embedded), a transformer and RJ45. It can be used as a component and no effort is required to interface W5500 and Transformer. The WIZ850io is an ideal option for users who want to develop their Internet...
Reference: RBD-0834
Glue Gun Sticks Hot melts easy use Multipurpose Perfect for home repairs, hobbies and crafts, Standard sealing wax sticks require less reloading. AC 100 V - 240 V, 50 Hz / 60 Hz Glue gun Uses standard hot melt glue sticks Fold-out stand for safe handy storage while in use. RoboticsBD
Reference: RBD-0920
Acrylic Body. Easy to install. compatible with HC-SR04
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-1626
Brand: RoboticsBD
Great for Starting with Arduino Programming A variety of components are included in this pack to try out different projects. The kit comes with quality components All-in-one kit, a great starter kit for learning to code. All Basis component to start is covered in kit You can create 15 different projects from this kit
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and...
Reference: RBD-0421
Compact and Portable pocket toolkit. RoboticsBD 44 different head style Rubber Shockproof gripped handle Strong and durable plastic Case Colour: Yellow-Light Green Interchangeable Precise Manual Tool Kit. High Strength Chrome Alloy is used to manufacture this tool. Magnetic bits are easy to fit into the handle. RoboticsBD Heat resistant.
Reference: RBD-0699
Display Size: 1.8″ Driver IC: ST7735 Input Voltage (V): 3.3 to 5 Pixel Resolution: 128 x 160 Interface Type: SPI
Reference: RBD-1138
Board Based On AI-Thinker A9 GPRS Module Supports Firmware Upgrade Via Serial Port Operating Voltage: 5v
Reference: RBD-1327
Package includes: 1 pcs x Acrylic Box ( without W1209 module ) DIY cover for W1209 Control Module Acrylic material looks transparent(may need to tear down the film). Easy for electronic enthusiasts to assemble.
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-1410
Compatible with Nvidia Jetson Nano Easy to assemble Slots to access all ports Cut-out for a fan at the top
Reference: RBD-2268
Features WiFi+Bluetooth connectivity with the ESP-WROOM-32 module Accessible I/O pins via extension headers for easy customization Onboard USB CH340 for convenient programming and debugging 2x keys for reset or user-defined functions ESP32S-DEV development board is a cost-effective solution for a wide range of applications.A high-quality USB cable is...
Reference: RBD-1039
The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...
Reference: RBD-1057
Low current leakage Light Weight and Offers good grip General purpose for all electronic applications. Advanced Heating element High-Quality Nickel-Copper plated Bit Quickly attains the working temperature Constant Tip temperature
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-2488
Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet 10BaseT/100BaseTX Ethernet PHY embedded Auto-Negotiation (Full-duplex and half duplex) Support Auto MDI/MDIX Simultaneously Supports to 4 independent sockets 0.18 µm CMOS technology 3.3V operation with 5V I/O signal tolerance Provide Serial Peripheral Interface (SPI MODE...
Reference: RBD-0727
Operating Voltage: 12VDC Power Consumption: 1.42 W Body and Blade Constructed from Thermoplastic PBT of UL 94V-0 Single Phase 4 Pole Brushless DC Motor Precise Vapo Bearing Counterclockwise Rotation Direction if Viewed from front of Fan Blade
Reference: RBD-1037
Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.
Reference: RBD-1087
Uninterruptible Power Supply Mini UPS Modem, Router, CCTV Camera and Lighting 6000mAh 22.2W
Reference: RBD-1692
Color: Black lightweight Convenient to carry this battery box holder with wires Weight: About 9g Wire Length: Approx 14cm
Reference: RBD-1152
Material: Metal, Plastic Power: 60W Temperature: 200-450°C (adjustable) Soldering Iron Length: Approx. 18.5cm Cable Length: Approx. 143cm
Reference: RBD-1390
Nema17 Bipolar. Number of Phases: 2. Step Angle: 1.8°. Phase Voltage: 2.6Vdc. Phase Current: 1.7A. Resistance: 1.5Ω ±10%. Inductance: 2.8mH ±20% (1KHz). Number of Wire: 4 (100cm Length). Holding Torque: 43N.cm. Shaft Diameter: Ø5mm. Motor Length: 40mm. Mass: 270g.