Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-0313
Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
Reference: RBD-0920
Acrylic Body. Easy to install. compatible with HC-SR04
Reference: RBD-1255
Integrated 0.96″ OLED Micro USB connection Compatible with Arduino Compatible with NodeMCU(Lua for ESP8266) Input Power 5V Compatible for Arduino Compatible with NodeMCU(Lua for ESP8266)
Reference: RBD-1069
Wheel Outer Diameter: 44MM Wheel width: 18 mm Tire material: Rubber Color: Black & White Weight: 18 gm Coder Accuracy: 12 pulses per revolution Wheel weight: 19.4 gm.
Reference: RBD-1412
Chipset :ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor FLASH: QSPI flash 4MB / PSRAM 8MB SRAM:520 kB SRAM Button: Reset USB to TTL: CP2104 Modular interface: UART,SPI,SDIO,I2C,PWM,TV PWM,I2S,IRGPIO On-board clock:40MHz crystal oscillator Working voltage:2.7V-3.6V Working current: About 70mA
Reference: RBD-1070
Dimensions: 22 x 15 mm (Diameter x Height) Weight: 10 gm Body Case Material: Plastic Ball Material: 304 Stainless Steel Application: for MiniQ robot
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-1557
USB communication, no need write code Support PC software automation Double antenna Support quad-band, universal worldwide Support 2G/3G/4G Automatically connect to the network Adaptive frequency
Reference: RBD-1765
LILYGO TTGO Model: 915MHZ CH9102F T3_V1.6.1 LoRa32 V2.1_1.6 Version 915Mhz ESP32 LoRa OLED 0.96 Inch SD Card Bluetooth WIFI Wireless Module ESP-32 SMA
Reference: RBD-1962
ESP32-S2-DevKitM-1 Equipped with ESP32-S2-MINI-1 module Easy interfacing Integrates ESP32-S2FH4 chip. PCB antenna 4 MB SPI flash.
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-1602
Microcontroller: ESP8266EX Operating Voltage: 3.3V Digital I/O Pins: 11 (all I/O pins have interrupt/PWM/I2C/one-wire capability, except for D0) Analog Input Pins: 1 Flash Memory: 4MB On-Board Switching Power Supply: Input Voltage Range: 9V to 12V Output: 5V at 1A Max
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-2137
ESP32 Development Board Integrated antenna and RF balun Dual-mode Wi-Fi and Bluetooth chips Small size and high performance-price ratio Compatible with Arduino
Reference: RBD-1708
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-0438
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD
Reference: RBD-1709
Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 18.6gm
Reference: RBD-1710
Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 12.6gm
Reference: RBD-2259
Type: Hexagonal coupling. Material: brass. Inner diameter: 3 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 14.6gm
Reference: RBD-2260
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-2261
Type: Hexagonal coupling. Material: brass. Inner diameter: 7 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-0702
It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock
Reference: RBD-2262
Type: Hexagonal coupling. Material: brass. Inner diameter: 8 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-2263
Type: Hexagonal coupling. Material: brass. Inner diameter: 8 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 18.6gm
Reference: RBD-1336
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...