Reference: RBD-0922

Slide Potentiometer 10K Linear Module Dual Output for Arduino

Dimensions: 91 x 21 x 30 mm(LxWxH) Weight: 18 gm. Voltage: 3.3V or 5V. Port: Analog. Resistance: 10K. Appn: Raspberry-Pi projects. DIY projects., Arduino projects.

Reference: RBD-2487

Hiwonder 6 Channel Digital Servo Tester with Over-Current Protection

6-channel PWM digital servo controller Supports a wide variety of PWM servos High-accuracy potentiometer for precise servo control Servo reset function 0.09° control accuracy 3-channel overcurrent protection Compact and lightweight design

Reference: RBD-1753

INMP441 Omnidirectional Microphone Module

Digital I2S interface with high precision 24-bit data High signal to noise ratio is 61 dBA High sensitivity – 26 dBFS Stable frequency response from 60 Hz to 15 kHz Low power consumption: low current consumption 1.4 mA High PSR: -75 dBFS

Reference: RBD-1183

Yellow Plastic Mag Wheel Soft Tire

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow

Reference: RBD-0430

Line Follower Sensor- 8 Array

Operating voltage: 4.5V to 5.0 V Output format: 8 Analog and Digital voltages. Optimal sensing distance: 0.125″ (3 mm). RoboticsBD

Reference: RBD-0034

Servo Motor MG996R 180 Degree Rotation

Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm

Reference: RBD-0432

JF-0530B Pull Push Type Electric Solenoid Electromagnet 10mm 5N DC12V

Iron Body Material High quality ultra-compact electric lock. RoboticsBD Rustproof, durable, safe, convenient to use. Suction which tightly sucks the iron, thus locking the door. Designed with the open frame type and mount board, high power. Easy to install for the electric door lock or other automatic door lock systems with the mounting board Applicable...

Reference: RBD-0419

SparkFun Particle Sensor Breakout - MAX30105

Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...

Reference: RBD-1707

4mm Hex coupling for Robot Smart Car Wheel 30mm Length

Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 21.6gm

Reference: RBD-1264

XIAOR Tracked Tank Chassis

Car body Material: Aluminum Alloy Car Wheel: Plastic Car strap: Plastic Color: Blue Input Voltage: 12V Weight: 1.2KG Motor & Tanks Chassis is included. No Electronics Parts

Reference: RBD-0231

Brand: SparkFun Electronics

Beaglebone Black - Rev C

Sitara AM3358BZCZ100 ARM Cortex-A8 32-Bit RISC microprocessor, up to 1GHz Onboard HDMI to connect directly to TVs and monitors More and faster memory now with 512MB DDR3L 400MHz SDRAM, 4GB eMMC Memory Onboard storage frees up the microSD card slot for greater expansion Support for existing Cape plug-in boards TPS65217C PMIC regulator and one additional...

Reference: RBD-0291

Sound Sensor Module for Arduino

Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.

Reference: RBD-0654

Male Pin Header Single Row (Short)

Single row. 2.54mm pitch. 1 x 40 pins. Through-hole mount. RoboticsBD

Reference: RBD-2106

Female to Female Jumper Wires 40 Pin 30cm

40P color jumper wires Length: 300mm Weight: 45 gm Compatible with 2.54mm spacing pin headers High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-0023

HC-SR501 PIR Motion Sensor

Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default)  Work temperature: -20-+80°C

Reference: RBD-0217

Servo Motor Micro MG90S 180 Degree Rotation

Model: MG90S Weight: 13 gm Operating voltage: 4.8V~ 6.6V Servo Plug: JR Stall torque @4.8V : 1.8kg-cm Stall torque @6.6V : 2.2kg-cm Note: The component, colour & shape of the motor may vary depending on our stock rotation.

Reference: RBD-1336

ESP8266 5V WIFI Relay Smart Home Remote Control Switch

Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...

Reference: RBD-1334

TP4056 Li-Ion Battery Charger with Protection

Charging current: 1A (maximum) Maximum charging voltage: 4.2V (1.5% accuracy) Input voltage: 4.5V-5.5V

Reference: RBD-2414

Yahboom 4 Channel Infrared Line Following Tracking Sensor Module

This tracking module adopts four tracking probes, and optimized spacing layout. The inner two probes can accurately identify the black line. The outer two probes can assist the inner probe to identify the black line and provide early warning. The car can recognize the 90°curved road and other difficult tracks. Knob-type adjustable resistors plus...

Reference: RBD-0409

4 Channel 5V Relay Board Module

No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...

Reference: RBD-0100

Robotic Claw - MKII With Metal Servo

Description: This robotic claw is a step up from the classic. The MKII takes everything you loved about the standard robot claw from DAGU and makes some significant improvements! 

Reference: RBD-2161

6 DOF Aluminium Mechanical Robotic Arm Manipulator Kit

Build a versatile robotic arm with six degrees of freedom. Control the arm with a microcontroller or compatible control system. Customize the arm with different end-effectors or tools. Learn about robotics and automation concepts while building your own robot arm. Perform small-scale industrial automation tasks with ease. Pick and place objects with...

Reference: RBD-0578

Robotics Claw Mechanical Gripper Clamp Kit

The degree of Freedom (DOF): 2 Paw material: aluminum alloy. RoboticsBD Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm

Reference: RBD-1534

Planetary Gear Motor PG42-775 42 Gear Box Large

Model:PG42-775 Working volt range:12V. Rated volt:12V No-loading Rotation speed:110-120 Rpm Speed Ratio:91

Reference: RBD-2074

5v Relay module for Arduino

Output SPDT Relay. Header connector for connecting power and trigger voltage. Screw terminal connector for easy relay output connection. Note: Relay might be different from the picture as per stock

Reference: RBD-0234

Brand: SparkFun Electronics

LCD Cape - pcDuino V3 (1024x600 7" LVDS)

Description: This is a 7" LVDS LCD Cape for the pcDuino V3  with a 1024x600 screen resolution and capacitive touch from  LinkSprite. This massive screen is a great addition for the  pcDuino V3 that compliments its extreme versatility as a mini  PC development platform. 

Reference: RBD-2251

BALA-C PLUS ESP32 Self-Balancing Robot Kit

ESP32-Pico-D4: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth Servo Rotation angle: 360 °; no-load speed: 0.12 seconds / 60 degrees (4.8V) Driver: L9110S Slave: STM32F030F4P6 Communication protocol I2C: 0x38

Reference: RBD-0150

5mW Adjustable Laser Dot Diode Module

Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~＋40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser

Reference: RBD-1912

L293D Motor Driver Module

New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)

Reference: RBD-1408

AMS1117 3.3V 5V/3.3V DC Mini USB Power Supply Module

Type: CJMCU MINI USB AMS1117 MINI USB interface input 5V MINI USB outputs 5V and 3.3V DC power socket interface input 5V – 12V. DC power outlet output (5V label) 5V and 3.3V Weight: 2 gm.