Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-0986
Ultra-thin design & adhesive backing provides easy integration to any project. Excellent price-performance ratio. Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting.
Reference: RBD-0376
Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes
Reference: RBD-0402
Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC
Reference: RBD-0280
Tie-points: 170 (10×17) Size: 48 x 35 x 10 mm(LxWxH). Use: experimental, testing, robot Matching jumper, diameter 0.8mm Phosphor bronze nickel plated spring clips Accepts a variety of wire sizes (29-20 the AWG) **1 pcs Random Color
Reference: RBD-2151
2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: RBD-1573
Supports up/down/left/right/middle with extra set and reset button 2V-9V wide working voltage The number of IO: 7 Operating temperature: -40℃ to 85℃ Size: 4×2.5cm
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0435
Supply Voltage : 8-35 VDC. Current : 1.0A (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.
Reference: RBD-0319
Type K Type. Mounting thread: M6 Temperature Range:0-600°C. RoboticsBD
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-1347
TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.
Reference: RBD-1606
Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C
Reference: RBD-1724
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
Reference: RBD-0663
Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD
Reference: RBD-1810
Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver
Reference: RBD-0416
Onboard 8 key TTP226 capacitive touch induction IC. RoboticsBD Onboard 8-way level indicator. Working voltage: 2.4 to 5.5 V. Modules, you can set the output mode, key output mode, the longest time and fast/low power output
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-0312
Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM
Reference: RBD-1063
Temperature Control Range(°C): -50 to +110 Resolution @-9.9°C to +99.9°C: 0.1°C Resolution @all temperatures: 1°C Accuracy: 0.1°C Refresh Rate(s): 0.5 Supply Voltage(V): 12 Measuring Inputs: NTC10K Cable Length: 0.5 Meter Output Type: 1 Channel Relay Output Capacity: 10A
Reference: RBD-1152
Material: Metal, Plastic Power: 60W Temperature: 200-450°C (adjustable) Soldering Iron Length: Approx. 18.5cm Cable Length: Approx. 143cm
Reference: RBD-1370
Name: PTV09A-4020F-B103 Package/Case: POT
Reference: RBD-1220
LCD Thermometer and Humidity Measuring Extended Sensor Sampling Period 10Sec Long-Lasting Battery
Reference: RBD-2086
Operating Voltage: 5V Contact Resistance : 50mΩ max (initial) Electrically Life:100,000 cycles Environment temperature: -25°C to +105°C Operating Force: 180/230(±20gf) Seal temperature:250ºC-280ºC I/O pins: 3 pins
Reference: RBD-2243
Wearable e-textile technology. Designed with large sew tabs Button Board
Reference: RBD-2244
Wearable e-textile technology. Designed with large sew tabs Slide Switch
Reference: RBD-2511
Switching a lot of power? N-channel power MOSFET - 30V / 60A IRLB8721 MOSFETs are just what you need.These TO-220 package power MOSFETs can switch 30V/60A, which is plenty for most makers! They fit straight into a breadboard or even your own PCB with 2.54mm spaced pads.
Reference: RBD-2317
The is a 4 way navigation switch (north, south, east, west) with a center push. Think of it as a mini joystick. Whilst the pins don’t align perfectly to a 2.54mm grid, it can be made to fit into a breadboard or perfboard by bending the pins.
Reference: RBD-2834
Enhance your 3D printer's performance with the DRV8825/A4988 Stable 42 Stepper Motor Driver Expansion Board. This expansion board offers advanced features and superior performance to meet your diverse needs in 3D printing and DIY projects.Note: Please ensure correct installation direction of the drive module to prevent module damage.
Reference: RBD-2411
Operating Voltage: 5V Pulse Number for One Circle: 20 Bi-directional Counting with No Limitation