How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0110
রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক। আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা 5V,3A. আমরা আমাদের টেস্ট এ 5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন। এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0696
Voltage : Input through (USB) DC 5V Output via (DC Round Pin) : DC 12V Color: BLACK Input / Output Current: Maximum Input 0.6 Easier for installation save time and money Easy to use.
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-0282
Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU
Reference: RBD-0963
Current and voltage display in turn, easy and comfortable to use. Small and portable, do not need other power supply. Measuring range: DC 3V – 9V / 0 – 3A (up to 5A ) Portable Device Interface: USB2.0, USB3.0 Product Weight: 0.025 kg Two output ports
Reference: RBD-1309
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin EU type. Output Plug: Micro USB Plug. Compatible with: Raspberry Pi B+, 2, 2B, 2B+,3 ,3B+, Zero, Zero W. It has a switch so you can easily power off the device without having to unplug it right from the socket.
Reference: RBD-0912
Model: 8020 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Rated RPM: 39000. Wire Length: 6cm Prop. Length: 55
Reference: RBD-1545
Input voltage 9~40V Output: 5V Maximum output current 2A Efficiency: 76-90% Material: electronic component
Reference: RBD-0950
Model : RS-360 micro-motors small pump Operating voltage : 4V-12V Current : 0.8A Motor diameter : 27 mm Pump Length : 52 mm Out of the water hole diameter : 4 mm Weight : 70g
Reference: RBD-1559
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-0951
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1560
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1114
N20 Micro Gear 12V 100RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel
Reference: RBD-1421
3S 11.1V 12.6V 20A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery). Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery). Continuous discharge current (upper limit): 20A (if the cooling environment is not good, please reduce the load current use). Continuous...
Reference: RBD-1340
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1341
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1697
Brand: DFRobot
Takes a 6-12V input voltage. Outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. Powered from 6-12 DC2.1 power jack or from USB power. The maximum current it can provide is 500mA.
Reference: RBD-1346
Model: SG92R Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 2.5kg-cm
Reference: RBD-1702
Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-0278
Model: MG995 Weight: 55 gm Operating voltage: 4.8V~ 7.2V Servo Plug: JR Stall torque @4.8V : 10 kg-cm Stall torque @6.6V : 12 kg-cm
Reference: RBD-1764
High Power DC-DC Step Down Module Input Voltage: 5-40V DC Output Voltage: 1.2-36V DC Efficiency: 95% Maximum Power: 200W
Reference: RBD-1874
Suitable for DIY & Hobby Kits, Routers, and Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved.
Reference: RBD-1876
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 1.8. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. Model: HS 121800
Reference: RBD-2140
220V Double Bearing DC Motor Dynamo Generator Efficiency: IE 2 Voltage: DC 220V Frequency: 50Hz Power factor: 0.85
Reference: RBD-1915
Input voltage range : 3-34V DC Output voltage range : 4-35v DC adjustable Output current:3A Voltmeter range:0 to 40V,error +-0.1v Multiple output regulator. One button to switch input and output voltage display. Power-down memory function. Press the button for 3 seconds can turn OFF/ON the LED display.
Reference: RBD-2121
Suitable for Arduino, DIY & Hobby Kits, and 6V servos and motor Rated Input AC Voltage 100v-240v It comes with a 1 meter long cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved.
