Reference: RBD-1101

5V Micro USB Tiny AVR ISP USBTinyISP Programmer Module For Arduino IDE Bootloader ISP Microcontroller

1 review

Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB

Reference: RBD-1102

ST LINK Stlink ST-Link V2 Mini STM8 STM32 Simulator Download Programmer

4 reviews

PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable! Interface definition directly marked on the shell, clear, convenient and practical! 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V Shell characters using laser engraving, never fade off! Permanent clarity! 500MA internal...

Reference: RBD-0034

Servo Motor MG996R 180 Degree Rotation

29 reviews

Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm

Reference: RBD-1212

USB to Serial RS232 DB9 Converter Cable

4 reviews

Single crystal 12M Tablet 340 USB port to serial port communication. USB1.1/2.0 compliant solution. Built-in 128 byte TX/512 byte RX buffer. Supports auto-Handshake Protocol. Support Win95/98/98se/ME/2000/XP/win7 32bit 64bit/Vista/supports full speed USB data transfer protocol. Design of electromagnetic interference. Data Exchange application. CH340 USB...

Reference: RBD-0912

8x20mm Coreless Motor with 55mm Propeller Pair

11 reviews

Model: 8020 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Rated RPM: 39000. Wire Length: 6cm Prop. Length: 55 

Reference: RBD-2198

CH341 USB Programmer

Model: CH341 Series Main Chip: CH341B Dimensions in mm (LxWxH): 85 x 28 x 12 Weight (gm): 20 8-bit parallel in EPP or MEM mode

Reference: RBD-0950

RS-360 Mini DC 4-12V Water Pump Motor

4 reviews

Model : RS-360 micro-motors small pump Operating voltage : 4V-12V Current : 0.8A Motor diameter : 27 mm Pump Length : 52 mm Out of the water hole diameter : 4 mm Weight : 70g

Reference: RBD-2412

USB ASP AVR Programming Device for ATMEL Processors Arduino

1 review

Compatible Chips:ATMega Series Tiny Series Classic Series CAN Series PWM Series You can also use this to recover your Arduino Bootloader

Reference: RBD-0951

N20 DC 6V 200RPM Mini Metal Gear Motor

6 reviews

This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.

Reference: RBD-2413

FTDI Basic Breakout USBTTL 6PIN 5V Module Fio/Pro/RGB/Lilypad Programmer

Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...

Reference: RBD-2416

WEMOS CH340G Breakout 5V 3.3V USB to Serial Module

5V (The max current depends on your USB port, usually 500mA) 3.3V (Using LDO, 300mA MAX) Use CH340G with stable performance. Driver: 1. CH340G USB to UART driver

Reference: RBD-1068

N20 12V 100 RPM Micro Metal DC Gear Motor

8 reviews

This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.

Reference: RBD-2427

USB Type-C Cable 1meter for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-1114

DC3-12V N20 Gear Motor & Mount Bracket & 43mm Wheel

3 reviews

N20 Micro Gear 12V 100RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel

Reference: RBD-2463

Programmer Testing IC Test Clip Black SOIC8/SOP8 Flash Chip IC Test Clamp

The SOP8 test clip is made of high-quality plastic and copper metal, which is durable and can be reused.When using the SOP8 test clamp, do not force it down, open the clamp and clamp it in from the left and right sides of the chip.The same is true when disassembling, you can't pull it out directly, you must first separate the clip from left to right, and...

Reference: RBD-1340

N20 12V 200 RPM Micro Metal DC Gear Motor

5 reviews

This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.

Reference: RBD-1341

N20 12V 300 RPM Micro Metal DC Gear Motor

12 reviews

This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.

Reference: RBD-1346

Mini Servo SG92R

8 reviews

Model: SG92R Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 2.5kg-cm

Reference: RBD-1165

Raspberry Pi 4 Acrylic Shell Case

5 reviews

9 Layer Acrylic stylish case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel

Reference: RBD-0347

Transparent Acrylic Shell Case for Raspberry Pi 3 Model B/B+

11 reviews

9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.

Reference: RBD-0278

Servo Motor MG995 180 Degree Rotation

9 reviews

Model: MG995 Weight: 55 gm Operating voltage: 4.8V~ 7.2V Servo Plug: JR Stall torque @4.8V : 10 kg-cm Stall torque @6.6V : 12 kg-cm

Reference: RBD-1242

Raspberry Pi 4 Acrylic Case

6 reviews

6-piece Acrylic case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble without any Screws or Nut-Bolts Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel Mounting holes and anti-slip rubber feet at the back.

Reference: RBD-1413

Brand: Raspberry Pi Official

Raspberry Pi Zero Official Case with GPIO and Camera Hole for Raspberry Pi Zero & Zero W

7 reviews

Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm

Reference: RBD-1309

Raspberry Pi Power Adapter with Switch Micro USB

11 reviews

Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin EU type. Output Plug: Micro USB Plug. Compatible with: Raspberry Pi B+, 2, 2B, 2B+,3 ,3B+, Zero, Zero W. It has a switch so you can easily power off the device without having to unplug it right from the socket.

Reference: RBD-0110

Raspberry Pi Power Adapter Micro USB

13 reviews

রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক।  আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা  5V,3A. আমরা আমাদের টেস্ট এ  5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন।  এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...

Reference: RBD-1702

Raspberry Pi 4 Power Adapter Type C

1 review

Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4

Reference: RBD-1144

5V 3A Power Supply Adapter Charger C-Type

15 reviews

Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin Type A Japan Output Plug: Type C

Reference: RBD-1156

Brand: Raspberry Pi Official

Raspberry Pi Zero Camera Adapter

6 reviews

FPC (Flexible Printed Circuit) cable. Length: 16cm. Ways: 15-way. Pitch: From 0.5mm(Raspberry Pi Zero) to 1.0mm (Raspberry Pi Camera and Raspberry Pi 3). Compatible with 5MP Raspberry Pi Zero W Camera.

Reference: RBD-1145

Micro HDMI Male to HDMI Male Cable for Pi 4 or 5

120 reviews

Version 1.4 HDMI to micro HDMI cable Supports 480i ,480p, 720p, 1080i, 1080p, 1440p resolution Cable Length: 1.5m Color: Black Application: Mulitimedia

Reference: RBD-2140

220V Double Bearing DC Motor Dynamo Generator Phase Resistance 400Ω

220V Double Bearing DC Motor Dynamo Generator Efficiency: IE 2 Voltage: DC 220V Frequency: 50Hz Power factor: 0.85

Reference: RBD-0168

Raspberry Pi Wedge Kit GPIO Breakout Expansion Board

8 reviews

Compatible With Raspberry Pi Module: T Type GPIO Extension Adapter Dimensions: 72 x 59 x 13 (LxWxH) mm. Pins: 40 Shape: T-Shape

Reference: RBD-1059

Black ABS Case With Fan Hole + CPU Cooling Fan For Raspberry Pi 3/2, 3B+

1 review

This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use. You just need to click them together after you fix your pi board on it with screws.