Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0234
Brand: SparkFun Electronics
Description: This is a 7" LVDS LCD Cape for the pcDuino V3 with a 1024x600 screen resolution and capacitive touch from LinkSprite. This massive screen is a great addition for the pcDuino V3 that compliments its extreme versatility as a mini PC development platform.
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0028
Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet. Stackable Design, can directly be supported by for Arduino official Ethernet Library. Supports up to four simultaneous socket connections Can be used to store files for serving over the network. Can be accessed using the Mini SD TF library. IEEE802.3af...
Reference: RBD-0412
Microchip's PICkit3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. The MPLAB PICkit3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price.
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-1097
Frequency: 125Khz. Support μEM4001, 4100, or its compatible RFID, ID card. Read first 10 digits of the RFID/Proximity card. Support Windows95/98/2000/XP/7/8. Plug and Play Reliable working condition Powered directly from USB, no need external power supply
Reference: RBD-0108
Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards. Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host) Supports HID devices, such as keyboards, mice, joysticks, etc. Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard...
Reference: RBD-0346
The PN532 is a highly integrated transmission module for contactless communication at 13.56 MHz including microcontroller functionality based on an 80C51 core with 40 Kbytes of ROM and 1 Kbytes of RAM. The PN532 combines a modulation and demodulation concept completely integrated for different kinds of contactless communication methods and protocols at...
Reference: RBD-0920
Acrylic Body. Easy to install. compatible with HC-SR04
Reference: RBD-1101
Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB
Reference: RBD-0159
Provides a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 6 keys select, up, right, down, left and reset. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage...
Reference: RBD-0313
Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-1102
PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable! Interface definition directly marked on the shell, clear, convenient and practical! 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V Shell characters using laser engraving, never fade off! Permanent clarity! 500MA internal...
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-1103
Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data. Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII. FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc. Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc....
Reference: RBD-1327
Package includes: 1 pcs x Acrylic Box ( without W1209 module ) DIY cover for W1209 Control Module Acrylic material looks transparent(may need to tear down the film). Easy for electronic enthusiasts to assemble.
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-1104
Isp interface: 6 PIN Isp interface: 10 PIN Power supply options: USB power Power supply options: external power supply (remove jumper cap)
Reference: RBD-1410
Compatible with Nvidia Jetson Nano Easy to assemble Slots to access all ports Cut-out for a fan at the top
Reference: RBD-0282
Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU
Reference: RBD-1099
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 1 to 5 cm (Depending on Antenna Geometry) Operating frequency: 125KHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anti-collision Printable Package Content: 1x Card
Reference: RBD-1106
XGecu Super Mini Pro T48 Universal Programmer
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-0306
Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android
Reference: RBD-1212
Single crystal 12M Tablet 340 USB port to serial port communication. USB1.1/2.0 compliant solution. Built-in 128 byte TX/512 byte RX buffer. Supports auto-Handshake Protocol. Support Win95/98/98se/ME/2000/XP/win7 32bit 64bit/Vista/supports full speed USB data transfer protocol. Design of electromagnetic interference. Data Exchange application. CH340 USB...
Reference: RBD-1692
Color: Black lightweight Convenient to carry this battery box holder with wires Weight: About 9g Wire Length: Approx 14cm
Reference: RBD-1817
USB Plug and Play. RFID reader 0-8cm Reading Distance. Win8/7/XP/Android Supported. S50/S70 Card Supported. OTG Phone Connection. Built-in buzzer and LED for identification.
Reference: RBD-1110
Supports a wide range of ATMEL AVR microcontroller. Works with AVR Studio or WINAVR(GCC) Works with ATMEL AVR Studio 4.13
Reference: RBD-1742
Holds 10 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 78X 60 X 28 Weight: 27.4 gm Material: Plastic Internal Connection: Series