Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0578
The degree of Freedom (DOF): 2 Paw material: aluminum alloy. RoboticsBD Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm
Reference: RBD-0227
Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm
Reference: RBD-0319
Type K Type. Mounting thread: M6 Temperature Range:0-600°C. RoboticsBD
Reference: RBD-0918
Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. RoboticsBD Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking.
Reference: RBD-1183
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-0320
Internal integrated cold junction compensation circuit. RoboticsBD With a simple three serial SPI interface; Temperature signal can be converted into 12-bit digital Embedded thermocouple break detection circuitry. High impedance differential inputs. Operating Voltage(VDC): 3 to 5.5 Temperature Range(°C): 0 to +1024 Cold Junction Compensation Range(°C):...
Reference: RBD-1707
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 21.6gm
Reference: RBD-1168
Item Name: TDS meter Meter Material: Plastic Display: LCD Digital Accuracy: +/- 2% Range: 0-9990 ppm
Reference: RBD-1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: RBD-1220
LCD Thermometer and Humidity Measuring Extended Sensor Sampling Period 10Sec Long-Lasting Battery
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-0357
Operating voltage (VCC): 3 V to 5V Operating current: 120μA (typical) 190μA (max) Operating Temperature: -40°C ~ +85°C Photodiode sensitive to UV-A and UV-B Embedded operational amplifier Analog voltage output Low supply current (300uA type) and low standby current (0.1uA type) RoboticsBD
Reference: RBD-0411
Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD
Reference: RBD-0415
Has a signal output instruction When the output valid signal is high, the light goes out The sensitivity is adjustable (fine-tuning) The wide detection range of vibration, no direction With mounting holes, firmware installation is flexible and convenient. RoboticsBD
Reference: RBD-1749
2 in 1 Type C USB Tester Color Screen LCD Digital Multimeter, Voltage Current Detector USB Cable Charger Indicator DC3.6-30V/0-5.1A
Reference: RBD-0331
Suitable for heavier goods and pressure resistance High elastic shock absorption for quiet operation Omni-directional wheel for flexible handling Thickened steel frame for increased bearing capacity Prevents floor damage from small objects
Reference: RBD-1824
Material: ABS Color: Yellow + Black Power: 2 x AAA Battery (NOT INCLUDED) Very Lightweight LED Light at tip for Dark sites
Reference: RBD-0493
Temperature Range : 0C-400C Shield Material : Metal Total Length(Approx.) : 2M / 6.6 Ft; Weight : 46g;
Reference: RBD-0553
Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds
Reference: RBD-2224
Voltage – 250V Easy PCB mounting Good consistency Widely acclaimed
Reference: RBD-0667
Input Supply Voltage (VDC): 3.3 ~ 5. Supply Current (mA): measurement 0.3mA standby 60μA. Temperature measurement range: 0~50 degrees. Temperature measurement error: ±2 degrees. Humidity measurement range: 20%~95%RH. Humidity measurement error: ±5%RH. RoboticsBD
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-0830
Thermocouples - K Type 800C WRN-291 200mm Rod 7.8 inch Rod/ 200mm Rod Temperature measurement range is from 0 celsius to 800 celsius degree. Screw Type
Reference: RBD-1173
Input Current : 100A Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Meet UL94-V0 flame retardant properties
Reference: RBD-1243
Resolution: 500dpi Supply current: <60mA Supply voltage: 3.3V Fingerprint image entry time: <1.0 seconds Peak current: <60mA
Reference: RBD-1249
Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 90mA
Reference: RBD-0568
Brand: Raspberry Pi Official
Fixed focus lens on-board Improved resolution – 8-Megapixel native resolution sensor-capable of 3280 x 2464 pixel static images Supports 1080p30, 720p60 and 640x480p90 video Size 25mm x 23mm x 9mm Weight just over 3g Connects to the Raspberry Pi board via a short ribbon cable (supplied) Camera v2 is supported in the latest version of Raspbian, Raspberry...
Reference: RBD-1671
ESP32 Bluetooth Wi-Fi development board, support NodeMCU / Arduino DHT11 temperature and humidity sensor CP2104 communication chip USB TO TTL Micro USB port Soil probe (long) soil temperature and humidity detection module 18650 Lithium Battery Holder Powered (Battery is not included)
Reference: RBD-1716
Working Voltage: 5.0V Maximum Working Current: 100mA Data Interface Level: L<0.8V, H>2.7V, maximum voltage level 3.3V Particle Measurement Range: 0.3 ~ 1.0μm; 1.0 ~ 2.5μm; 2.5 ~ 10μm Note: Please purchase this adapter board to use it with Arduino and Raspberry Pi.
Reference: RBD-1719
Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December
Reference: RBD-1727
This is 38KHz Infrared IR transmitter sensor module For Arduino Transmit 38KHz modulating signal Suitable for Arduino DIY project Material: PCB